This specification covers aluminum and aluminum alloy flat sheet, coiled sheet, and plate in the alloys
Alloy and temper designations are in accordance with ANSI H35.1.
Equivalent standard in Chinese: GB/T3190 for chemical composition and GB/T3880 for mechanism properties.
General Quality:
Unless otherwise specified, the material shall be supplied in the mill finish and shall be uniform as defined by the requirements of this specification and shall be commercially sound. Any requirement not covered is subject to negotiation between producer and purchaser.
Each sheet and plate shall be examined to determine conformance to this specification with respect to general quality and identification marking. On approval of the purchaser, however, the producer may use a system of statistical quality control for such examinations
Alloy: From 1000 series to 8000 series,
Commonly used: 1100, 1050, 3003, 3105, 5005, 5052 etc
Temper: Hard (H18/H28), semi-hard(H14/H24), soft and annealed (O)
Size: Thickness from 0.2mm~25mm approximately
Width: 700~2400mm approximately
Surface: Mill finished with bending angle, embossed, tread available,
Tolerance: Edge trim, accord to ASTM H35 and GB/T 3880
PVC fim available
| Alloy |
Temper |
Thickness(mm) |
| 1235 |
H12, H22 |
> 0.20-4.50 |
| H14, H24 |
> 0.20-3.00 |
| H16, H26 |
> 0.20-4.00 |
| H18 |
> 0.20-3.00 |
| 1070 |
F |
> 2.50-8.00 |
| O |
> 0.20-6.00 |
| H12, H22, H14, H24 |
> 0.20-6.00 |
| H16, H26 |
> 0.20-4.00 |
| H18 |
> 0.20-3.00 |
| 1060 |
F |
> 2.50-8.00 |
| O |
> 0.20-6.00 |
| H12, H22 |
> 0.50-6.00 |
| H14, H24 |
> 0.20-6.00 |
| H16, H26 |
> 0.20-4.00 |
| H18 |
> 0.20-3.00 |
| 1050, 1050A |
F |
> 2.50-8.00 |
| O |
> 0.20-6.00 |
| H12, H22, H14, H24 |
> 0.20-6.00 |
| H16, H26 |
> 0.20-4.00 |
| H18 |
> 0.20-3.00 |
| 1145 |
F |
> 2.50-8.00 |
| O |
> 0.20-6.00 |
| H12, H22, H14, H24, H16, H26, H18 |
> 0.20-4.50 |
| 1100 |
F |
> 2.50-8.00 |
| O |
> 0.20-6.00 |
| H12, H22 |
> 0.20-6.00 |
| H14, H24, H16, H26 |
> 0.20-4.00 |
| H18 |
> 0.20-3.00 |
| 1200 |
F |
> 2.50-8.00 |
| O |
> 0.20-6.00 |
| H12, H22, H14, H24 |
> 0.20-6.00 |
| H16, H26 |
> 0.20-4.00 |
| H18 |
> 0.20-3.00 |
| 3003 |
F |
> 2.50-8.00 |
| O |
> 0.20-6.00 |
| H12, H22, H14, H24 |
> 0.20-6.00 |
| H16, H26, H18 |
> 0.20-4.00 |
| H28 |
> 0.20-3.00 |
| 3004 3104 |
F |
> 2.50-8.00 |
| O |
> 0.20-6.00 |
| H12, H22, H32, H14 |
> 0.20-3.00 |
| H24, H34, H16, H26, H36, H18 |
> 0.20-1.50 |
| H28, H38 |
> 0.20-3.00 |
| 3005 |
O, H111, H12, H22, H14 |
> 0.20-6.00 |
| H16 |
> 0.20-4.00 |
| H24, H26, H18, H28 |
> 0.20-3.00 |
| 3105 |
O, H12, H22, H14, H24, H16, H18 |
> 0.20-3.00 |
| H28 |
> 0.20-1.50 |
| 3102 |
H18 |
> 0.20-3.00 |
| 5182 |
O |
> 0.20-3.00 |
| H19 |
> 0.20-1.50 |
| 5A03 |
O, H14, H24, H34 |
> 0.50-4.50 |
| 5A05, 5A06 |
O |
> 0.50-4.50 |
| 5082 |
H18, H38, H19, H39 |
> 0.20-0.50 |
| 5005 |
F |
> 2.50-8.00 |
| O |
> 0.20-6.00 |
| H12, H22, H32, H14, H24, H34 |
> 0.20-6.00 |
| H16, H26, H36 |
> 0.20-4.00 |
| H18, H28, H38 |
> 0.20-3.00 |
| 5052 |
F |
> 2.50-8.00 |
| O |
> 0.20-6.00 |
| H12, H22, H32, H14, H24, H34 |
> 0.20-6.00 |
| H16, H26, H36 |
> 0.20-4.00 |
| H18, H38 |
> 0.20-3.00 |
| 5083 |
O |
> 0.50-4.00 |
| H22, H32 |
> 0.50-4.00 |
| 8006, 8011, 8011A |
O |
> 0.20-3.00 |
| H14, H24, H18 |
> 0.20-3.00 |
