Home > Products > Electronics & Electricity > Other Electrical & Electronic

OVERVIEW

The ULT-3000 contains all of the functions required for studying and experimenting with analog electronics, digital electronics, telecommunication electronics etc. The ULT-3000 is a complete analog and digital training platform which is compact, lightweight and extremely durable.

APPLICATIONS  

• Basic Electronics Training Courses
• Advanced Electronics Circuit Design
• Analog Circuit Experiments
• Digital Circuit Experiments
• Telecommunication Circuit Experiments
• Basic Logical Circuit Tracing
• Computer Interfacing Circuits
• Circuit Trouble Shooting

SPECIFICATIONS

1.      DC Power Supplies Module

Fixed Output: +5V/1A, -5V/1A, +12V/0.5A, -12V/0.5A

Variable Output: +0V ~ +24V/1A, -0V ~ -24V/1A

All power supplies are short circuit protected

2.      AC Power Supplies Module

19V–15V–9V–0V–9V–15V-19V

3.      Function Generator (2 Channels) & Clock Generator (2 Channels) Modules

Sine, Triangle and Square waveform output

Frequency range: 1Hz to 1MHz in 6 decades

With fine adjust, Amplitude and DC offset control

Clock output 1Hz to 1MHz in 6 decades

Six frequency ranges:

     1Hz to 10Hz

     10Hz to 100Hz

     100Hz to 1KHz

     1KHz to 10KHz

     10KHz to 100KHz

     100KHz to 500KHz

Sine wave output: 0 to 12V peak to peak variable

Triangle wave output: 0 to 8V peak to peak variable

Square wave output: 0 to 22V peak to peak variable

4.        Solderless Breadboard Module

Interconnected nickel plated with a total of 1860 tie points nickel plated contact, fitted all DIP sizes and all components with lead and solid wire in diameter of AWG #22-30 (0.3-0.8mm)

5.      Two Pulse Switches Module

          80uS Single Shot Pulse (Positive & Negative)

2 units push button switch contain switches debouncer for eliminating the bounce caused by switch from “open” to “close” or from “close “ to “open” position.      

6.      Two digits 7-segment LED Display Module

       Numerical designs and resultant display                        Truth Table

7.      16-Bits LED Indicators with buffer Module

Sixteen LED’s separate input terminals in three colors. (RED, Yellow & Green). The LED will be lighted up when input is at “HI Level”, and it will be turned off when it is at no input or at “LO Level”. Capable for Traffic Light Experiments.

8.      16-Bits HI/LO Data Output Switches Module

16 units slide switches and corresponding output terminals. When switch is set at “down” position, the output is LO level; contrarily, it is to be HI level when setting at “up” position.

9.      TTL/CMOS Selection Switch

       Select TTL or CMOS Mode for data switches

10.   3-State Logic Probe Module

       HI, LO, FLOAT 3 Logic Level Testing

       CMOS / TTL Level Selection

11.   Speaker Module

       8Ohm, 0.25W With Buffer

12.   Digital DC Volt Meter Module

       4 Digits LED display  

       Four voltage ranges: 

            0V to 199.9VDC                                 

            0V to 19.99VDC 

            0V to 1.999VDC                   

            0V to 199.9mVDC  

       Input Impedance: 10Mohm for any range

13.   Adaptors Module

       5 Channels Banana to 2mm Adaptor Interface Socket and turn pins sockets

14.   Universal Connector Fixed Holder Module (Optional)

It reserves universal connector fixed holder on the panel in order to be connected with various universal connectors, which are available listed as follows:

       UC-01: Straight Header 60 pin

       UC-02: Card Edge Connector 2.54mm 62 Pin

       UC-03: Card Edge Connector 3.96mm 28 Pin

       UC-04: RS-232 Connector 25 pin D-Sub Connector (Male & Female)

UC-05: USB Connectors

       UC-06: Centronics / Parallel 2.54mm 36 Pin

The ULT-3000 is shipped with a comprehensive CD Format Experiments Manual, Instruction Manual with Self Maintenance Guide and a power cord.

Power Supply : 240VAC, 50Hz (Fused Protected)

Dimensions : (W x D x H) 310 x 260 x 90mm

Weight : 3.5 kgs