Home > Products > Industrial Supplies > Electrical & Electronic Product Equipment

Reliable flame detector (oil, coal and lignite flame)
Forney US company (FORNEY) type IDD-II intelligent dynamic flame flame detector capable of oil, coal and lignite flame flame accurate detection and identification.
IID-IIU flame detector is used to detect oil and coal flames flames. IID-IIL flame detector is used to detect lignite flame.
IDD-II intelligent dynamic flame detector is a company and Forney (FORNEY) fire detection amplifier DR-6161E, DR-6101, RM-IDD, IDD-IIIA join together to use. IDD-II-type flame detector detects the flame, the ripple voltage signal detection circuit and its hardware components produced by amplifying the signal amplified by the four-core shielded cable to the amplifier. After the signal processing amplifier output signal to the burner management system.
Flame detector electronics are encapsulated in a cast aluminum housing. Amplifier periodically self-test to determine whether the flame detector is working properly.

Product Features:
1. PbS photoelectric sensors:
Oil, coal and lignite flame infrared and visible light detection.
2. Dynamic flame detection circuit:
Produced only a dynamic flame signal without detection of thermal radiation.
3. The structure is simple and durable way:
Circuit boards and sensitive components are packaged in aluminum housing, as replacement parts.
4. easy installation and maintenance:
Fast electrical and mechanical contact, easy installation and maintenance.
5. Meet the FM certification

IDD-II intelligent dynamic flame detector
Products and installation accessories
IID-II has a filter (# 6 coal and oil)
IID-IIU no filter (# 2 oil and gas)
IID-IIU no filter (# 2 oil and gas)

Forney flame detector, amplifier United States Forney, Forney flame amplifier, detector Forney, Forney flame detectors, flame sensors Forney, Forney flame relay, Forney ultraviolet flame sensor, processor Forney, Forney infrared probes
Forney PM-DR-6101E amplifier device is a stand-alone intelligent controller consists of two printed circuit board placed in a covered base (PCB) components. Which comprises a combination of a PCB power relay and input / output (I / O) interface software. Another PCB including a microprocessor, a stabilizer and the signal processing electronics. The entire device can be installed in a single equipment cabinet. Can be equipped with fire detection probes have: IDD-II with filtered infrared probe, IDD-IIU without filter infrared sensor, UV-4 probe, DR-6 IDD / UV probe.
D furnace flame detector Uniflame 95 series

Overview: FORNEY UNIFLAME Series flame detectors are microprocessor-based flame detector, using a solid-state infrared sensor (IR), ultraviolet sensor (UV) and dual sensor (IR UV). All with internal flame detector relay, and adjust the ON / OFF thresholds, so no remote flame amplifier. UNIFLAME \ 95 series both FORNEY DPD detector flame detector principle and characteristics, can detect single or multiple burner flame burner conditions with or without the target. UNIFLAME \ 95 series detector detects amplitude modulation (ie flickering flame characteristics) target produced by a fire. In the detector setup process, select to generate a modulated frequency characteristic of the best flame ON / OFF resolution. And can be adjusted manually or automatically to select the appropriate modulation frequency and sensor gain. UNIFLAME \ 95 series detectors with automatic programming (self-learning) function; 21 kinds of flame flicker frequency selection; 4 optional programming file to store the set value; FORNEY also increased through the use of user-based application WINDOWS95 / 98 / NT's remote communication software. All UNIFLAME \ 95 detectors require 24VDC power supply with 12-pin quick connector, an electronic self-test function (no mechanical shutter required). Detector with an 8-bit number / letter LED display and four buttons for easy user to view operating parameters and select the setting.

application:

IR type: includes an infrared flame sensor that is adapted to the case of oil and coal fuel. UV type: includes a UV flame sensor that is adapted to the case of gaseous fuel and light oil fuel.

DS :( dual sensor type) comprises two kinds of the infrared and ultraviolet flame sensor that is suitable for the case of multi-fuel.

Uniflame series Ibid installation accessories: mechanical accessories mounting flange plate (be) whether the detector is installed or direct endoscopic fiber optic installation, you need to use the disk mounting flange, plate flange mounted external interfaces to 1 "NPT female thread duralumin material. universal joints (direct endoscopic optional) ?? detector universal joint is installed after the detector is used to adjust the viewing angle of the detector. insulating tube (direct endoscopic must) compartment heat pipe, heat to the detector is to prevent heat from the observation tube, while the detector with earth electrical insulation corresponding observation tube with mounting flange ordered with quartz window (direct endoscopic optional) quartz window, when it is detected It needs to be sealed or connected to use quartz window to block the furnace pressure, hot gases and ash, making it impossible to close the detector or contaminated lenses. specification is one inch US standard taper thread when needed sealed with a 1-inch tee connection so that the cooling air through the fiber optic components (fiber type must) fiber optic assembly includes an outer catheter assembly within the catheter assembly, fiber optic components, furnace wall mount assembly. in the burner structure is complex and multi-burner combustion boilers, using fiber optic components can be flame "flash" signal is transmitted through the optical fiber from the furnace to facilitate monitoring of the detector electrical accessories detector cable FORNEY provide UNIFLAME \ 95 series detectors dedicated 12-cell foil fully shielded cable this cable includes six # 18AWG and four # 22AWG wire, plus one pair of # 22AWG twisted-pair cable jacket is the result of a polyolefin material processing (flame retardant, low, zero halogen) maximum diameter of 0.43 "( 10.9mm). Each detector longest cable up to 1000 feet. This raw rubber cables require the following quick connector. Quick access UNIFLAME \ 95 series detector comes factory-core cable 12 male connector, FORNEY provides matching female cable connector, easy on-site installation. Referring aviation plug attachment instructions. Prefabricated cable with 12-pin cable adapter provides the FORNEY, the length can be scheduled with the female connector at the factory. The annex ranging in length from 10 feet (3m) to 300 feet (91m). Junction box assembly if desired distance telecommunication, UNIFLAME between the detector and the control room more than 200 feet (61M), then each detector must be connected to a junction box. In the junction box, two communication lines must be connected with the 12-pin cable separately, in the circulation loop, multi-point tandem configuration (daisy chain) connected to each detector, and finally to the computer.

FORNEY junction box assembly, ranging in length from 3-30 feet (0.9 to 9.1 meters), offers a convenient wiring. At one end of the junction box are quick connector to UNIFLAME detector. FORNEY 12 core cable shipped with quick connector, the flexible cable can be connected to the junction box in the other terminal. Terminals can be connected to 14AWG wire, clamp connectors can be quickly and securely connected with the press-fit type. Through the junction box, the installer can connect all the wiring, but FORNEY 12 core cable reaches the burner management system in the two lines are not connected. Two communication lines from the detector up and down with the junction box must be connected to the computer through a final two-core communication cable. 24VDC power supply FORNEY provide 24VDC power for 95 Series flame detectors.

Union Electric Co., Ltd. Nanjing Yun supply advantages, imported, quality assurance, adequate supply, welcome to inquire.