| Model: | Q2603 |
|---|---|
| Brand: | XINSA |
| Origin: | Made In China |
| Category: | Industrial Supplies / Machinery / Cleaning Machine |
| Label: | Sand blasting , chamber |
| Price: |
US $44776
/ pc
|
| Min. Order: | 1 pc |
| Last Online:27 Feb, 2019 |
Qingdao xinsa machinery manufacturing Co., Ltd,independent R&D design this pitless pneumatic recycle sandblasting room.the only one that owns this technology of pitless sandblasting room all over the word.
Comparison of Environmental Protection Pneumatic recovery Sandblasting room's characteristics with Mechanical Recycling Sandblasting room
1,Low cost of integrated operation and energy saving.
Pneumatic recovery Sandblasting room mode with no transmission mechanism is adopted, and the failure rate is low and maintenance is free. Reduce the maintenance time of the shutdown, and reduce the loss caused by the shutdown and maintenance;
2,the honeycomb floor has a sand-back structure without digging pit, and the civil engineering cost and the construction period are greatly reduced;
3,The structure is simplified and the interlocking control can be used in each system control, which greatly improves the convenience of maintenance and repair.
4,The key wear parts are equipped with standard modules, which are easy to maintain and replace, thus avoiding heavy maintenance work.
5,The sandblasting chamber adopts the upper supplementary air, the lower part and the side part can carry on the dust suppression circulation mode. The dust always drains downward, the visibility in the room is high, the working environment is good, the quality and efficiency of sand blasting are guaranteed, and the physical and mental health of the workers is protected.
6,The whole sand absorbing floor can recover all the sand materials in an instant, and there is no residual sand material on the ground. The sand blasting room is clean and clean in the room, no manual cleaning is required, and the working time is saved. Pneumatic pipe back sand, abrasive recovery up to 99, easy to clean the abrasive. Traditional mechanical recovery (or scrape floor) sandblasting room is almost impossible to thoroughly clean and replace abrasives.
7,The body of sandblasting room is simple and beautiful, and the installation is convenient and flexible.
8,The whole technical performance of sandblasting room is advanced, dust emission meets and is lower than the national and local environmental protection requirements, and the environmental pollution is completely eliminated.
| Item | Unite | Numerical value | |||
| Inner measurement of sand blasting room | length×Width×height | mm | 5000×4000×3500 | ||
| Sand blasting door dimensions | Width×height | mm | 3000×3000 | ||
| Max workpiece weight | (ton) | 5 | |||
| Cleaning workpiece speed | External surface of profiled structural parts
|
sq.m./h | 20-30(A-D grade according the different cleaning requirements of original Surface material and workpiece
|
||
| cleaning quality rank | reach Sa2 .5 rank | ||||
| Processing material and strength range | Q235/Q345/65Mn/HT/ZG etc. | ||||
| surface roughness | μ | 40~75depend on the shot ball's size) | |||
| Total power | kw | about 20.5 | |||
| Compressed air consumption | m³/min | 6,each spraying gun need 5 m³/min,protecting air-condition and the back flush dust cleaning need 1 m³/min | |||
| Compressed air pressure | MPa | 0.5-0.7 | |||
| facility adaptive temperature | Suitable for local four seasons normal temperature | ||||
| control system | electrical appliance control system | Manual button control
|
|||
| Ground pit requirement | Can have no pit, waterproof
|
||||
| overall noise | dB | ≤95 | |||
| dust discharge concentration | mg/m3 | 80mg/m3excel the 80mg/m3 of the GB16297-1996<emission standard of air pollutants> | |||
| dust content in the air after cleaned | mg/m3 | 10 |
|||
According to your requirements, the most suitable machine will be designed for your workpieces, please indicate the following details.
1. What kind of workpiece you clean?
2. The workpiece size, length, width, height and weight of maximum workpiece.
3. What's your production capacity per day (8 hours)?
4. It's my pleasure if you can provide details workpiece photos to us.
Based on these details information, the detailed technical proposals will be sent to you for reference.
FAQ
1. How many days do you need to produce this machine?
This is specially designed machine according to your specific requirement. From engineer designing to production completion, It needs about 45-50 days.
2. What does your factory do regarding quality control?
We pay much more importance to quality control from the very begining to the end of production. Every machine will be fully assembled and carefully tested before shipment.
3. What's your machine quality guarantee?
Quality guarantee time is one year, we choose world famous brand components to keep our machine in perfect working condition.
4. Are you able to give installation and commissioning overseas? How long will it take?
YES, we supply overseas service, but customer needs to pay for the engineers flight tickets and hotel foods.
Small machine usually takes within 5 days.
Big machine usually takes about 20 days.
Sale manager:ALINA
