Home > Products > Industrial Supplies > Machinery > Machine Tool

Taiwan HIWIN miniature guide rail MGN7C small slide block 1Taiwan HIWIN miniature guide rail MGN7C small slide block 2Taiwan HIWIN miniature guide rail MGN7C small slide block 3Taiwan HIWIN miniature guide rail MGN7C small slide block 4Taiwan HIWIN miniature guide rail MGN7C small slide block 5
  • Taiwan HIWIN miniature guide rail MGN7C small slide block 1
  • Taiwan HIWIN miniature guide rail MGN7C small slide block 2
  • Taiwan HIWIN miniature guide rail MGN7C small slide block 3
  • Taiwan HIWIN miniature guide rail MGN7C small slide block 4
  • Taiwan HIWIN miniature guide rail MGN7C small slide block 5

Taiwan HIWIN miniature guide rail MGN7C small slide block

Model:MGN7C
Brand:HIWIN
Origin:Made In Taiwan, China
Category:Industrial Supplies / Machinery / Machine Tool
Label:HIWIN , MGW15 , MGN9C
Price: ¥100 / pc
Min. Order:1 pc
Inquire Now

Member Information

Detail

Product Description

MG series small linear slide MGN:

 

1: Lightweight and lightweight, especially suitable for miniaturized equipment.

 

2: Slider and slide rail are available in stainless steel and alloy steel. Stainless steel linear slides, including sliders, slides and other metal accessories such as steel balls,

 

3: The holders are made of stainless steel and have anti-rust properties.

 

4: Gothic four-point contact design, can withstand loads in all directions, with strong rigidity and high accuracy.

 

5: With steel ball protector design, interchangeable with accuracy allowed.

 

HIWIN linear slide rail miniature rail model:

 

MGN7C MGN9C MGN12C MGN15C MGN7H MGN9H MGN12H MGN15H

 

MGW7C MGW9C MGW12C MGW15C MGW7H MGW9H MGW12H MGW15H

 

MR5MN MR7MN MR9MN MR12MN MR15MN MR5ML MR7ML MR9ML MR12ML MR15ML

 

MR5WN MR7WN MR9WN MR12WN MR15WN MR5ML MR7WL MR9WL MR12WL MR15WL

 

Preparations before installing the silver linear guide

 

1. Calibration of machine level.

 

Requirements: Use two contour blocks and a marble ruler on the mounting base, and put a precise spirit level on the base to adjust the base level.

 

2. Check the surface roughness, flatness, straightness and appearance of the rail mounting base.

 

Requirement: After the horizontal adjustment is completed, the laser rail interferometer must be used to measure the flatness of the main rail mounting base surface (we usually use a rail surface near the right column as the main rail). The flatness is allowed to be 0.05mm in every 10m, and the full stroke is straight The degree of allowance is 0.03mm. Roughness requirement of 1.6, no casting defects in appearance.

 

3. The chamfering of the rail mounting base surface and the rail side reference mounting surface.

 

Requirements: The chamfer radius is less than or equal to 3.5mm. If the chamfer is found to be too large or protruding, you should use oil stone and file in time, otherwise it will cause poor installation of the guide rail accuracy or interfere with the slider.

 

4, the processing of rail mounting base surface locking threaded holes.

 

Requirement: Confirm whether the position of the installation screw holes is correct. The center distance of each connected screw hole is greater than 0.1mm or less than 0.1mm. To ensure high-precision screw hole processing, CNC positioning is required.

 

5. Inspection of guide rails after unpacking.

 

Requirement: Check whether the guide rail has a certificate of conformity, whether there is any injury or rust, clean the anti-rust oil, and remove burrs, bumps and dirt on the assembly surface.


Product Image

Taiwan HIWIN miniature guide rail MGN7C small slide block 1
Img 1
Taiwan HIWIN miniature guide rail MGN7C small slide block 2
Img 2
Taiwan HIWIN miniature guide rail MGN7C small slide block 3
Img 3
Taiwan HIWIN miniature guide rail MGN7C small slide block 4
Img 4
Taiwan HIWIN miniature guide rail MGN7C small slide block 5
Img 5

Send Inquiry to this Member

Dongguan Geyang Electromechanical Equipment Co., Ltd.

1st floor, No. 3, Paijiji Education Road, Wanlou Street, Wanjiang District, Dongguan City, Guangdong Province

Phone:
+86-0769-8997451
Fax:
Contact:
Mr. Chen (Engineering procurem)
Mobile:
18824524163

Related Products of this Company

This member assumes full responsibility for the content of this listing. DIYTrade accepts no responsibility whatsoever in respect of such content.
To report fraudulent or illegal content, please click here.

China Suppliers Quick Searching:

Machine Tool Made In China Products

,  

Machine Tool China Suppliers and China Manufacturers