Home > Products > Home Supplies > Personal Care Appliance

Decomposition Principle of frozen fat

◎What is the decomposition of frozen fat?

Decomposition of Frozen fat is a new technology that reduces fat cells by non-invasive use of controlled cooling energy.

It delivers strong cooling power to the treatment site to make fat cells crystallized and then achieve fat cell apoptotic. The treated fat cells die and then naturally fall off the body.

 

What is a Frozen Body- Shaping

Instrument

◎The frozen slimming Instrument is used for the decomposition of low temperature fat in the body.

By controlling the cooling energy delivered to the target body area, freezing the subcutaneous fat cells which is suitable for elimination.It reduces the thickness of fat and makes the body symmetrical.

Advantages Of Frozen Body-Shaping

Instrument

◎The optimum size for cold highlights

Concise design and simple white attract users' attention.In addition, using the optimal size to improve usability, enhance performance, and provide satisfaction.

◎Convenient adjustment function

Accurately it can adjust temperature and pressure to properly deliver  the cooling energy to subcutaneous fat cells.

◎Four-dimensional twist shapers

Precise Shaper is tightly attached to selected parts without pressure loss, it could cover different parts of the body.

◎Further increasing the flexibility of the frozen slimming instrument

The frozen slimming instrumentprotects the skin from cooling energy while improving the effectiveness of the product, and has  effects on imparting elasticity, nutrition, moisture, etc.

◎Is this treatment safe?

It’s very safe. This is because the controlled cooling power only affects the fat cells and does not damage other cells and tissues of the body.

◎Is there any pain or side effect?

A few minutes after starting treatment, the curer will experience temporary pain or discomfort. However, due to the cooling power, the treatment site will immediately become numb and the pain and discomfort disappear. Stress may cause erythema, bruising or sparse foaming to a few curers.

◎Can the curers return to normal activities after treatment?

Yes. After treatment, the curer can perform normal daily activities immediately.

◎Where is the fat going?

The cooled crystalline fat cells die and are naturally metabolized by the body as lymph Detoxification.

Advantages and Comparison Of Frozen Body-Shaping Instrument

 

 

 

◎How long is each treatment?

The length of treatment depends on the body part of the treatment and the skin condition of the individual.

Our recommendations for treatment time for various parts of the body are as follows:

A relatively wide body part (such as the abdomen, small belly, thighs, etc.) need 40 to 60 minutes each time,and narrow body parts need 20 to 30 minutes.

◎How many treatments do we need to get results?

It depends on the condition of the curer and the treatment site.We usually recommend as e follow:

-Wider parts (such as abdomen, small belly, thighs, etc.) are recommended to be done once every two or three weeks ,totally four treatments as a course.

- Narrow body part is treated once every 20-30 days, and the second treatment can be performed 3 weeks after the first treatment.

◎When can the curer have an effect?

The effect occurs according to different curers and the different treatment sites, and normally after two or three weeks of treatment, you will see the effect.

◎Does the curer need to combine other special treatments?

It’s recommended to combine the following operations:

- Before the frozen slimming treatment, high-intensity focused ultrasound therapy or massage, interval RF can make the effect of  treatment better.

-After the frozen slimming treatment, you need enough massage to smooth the detoxification after lymphatic surgery.

- Drinking enough boiled water also helps lymphatic detoxification.

◎Does the Antifreeze Mask have an effect on the bonding of the equipment?

Yes,Because the antifreeze mask protects the surface of the skin during treatment. In addition, it contains formulas to prevent frostbite, which control the cooling power directly irritating the skin during treatment.

Interface Introduction Of Frozen body-shaping device

 

 

Safety Of Frozen body-shaping instrument

Controlled cooling energy only affects fat cells and cryo-pad gels which effectively protect skin surfaces and other tissues

 

Therapeutic accessories

 

 

 

Components of frozen body- shaping instrument

 

Installation Technique of Frozen Body- Shaping Instrument  - Check the sensor cover and liquid filter cotton

Make sure that the yellow filtered cotton is installed inside the sensor cover.

 Equip shaping gel

Equip the shaping gel which is required for treatment on the machine to prevent air leakage (FIG 1).

-Insert frozen protective film

1.Take out a piece of frozen protective antifreeze mask from the bag and apply the essence of it to the shaping gel.

*Apply the remaining essence of the antifreeze mask to the location to be treated.

1. Take out a piece of antifreeze mask, put it on the mouth of the main body of the instrument, and then snap it into the silicone of both side.

*Never remove the capping glue from the antifreeze mask

*The center line of the antifreeze mask is parallel to the shaping gel. (FIG 2)

1. It is necessary to press the sides of the antifreeze mask and stick it to the groove of shaping gel（ FIG. 3 ），so that the pad marks which the antifreeze mask leaves will not stain on the skin during the treatment.

4. Make sure the antifreeze mask must be close attached to the frozen plate so that the antifreeze mask is attached to the frozen plate red label position (FIG. 4)

Connection Of Shoulder Strap

 Connect the shoulder strap to the silver circle on the back of

the instrument, and follow the steps as below（FIG5.FIG6）

Procedures of starting the Frozen Body-Shaping Instrument

Select surgical site> Install shaping gel> Insert antifreeze nask> adjust time/press/time / pressure / temperature>start-up

Precautions of Frozen Body Shaping Instrument

- The antifreeze mask must be stuck on both sides of the colding plate before using it.

- It can work continuously for 24 hours. The longer the working hours, the better the refrigeration effect

- Please check if the yellow filter cotton is wet during preparation. If it is wet, please replace it. Generally, it needs to  be replaced after using it 3-5 times. It can be washable but it must be dried before used.

- The antifreeze mask is disposable.

- After using the instrument, please keep it clean.

- After the treatment, the antifreeze mask should be taken out, and then the instrument must be placed upright (If the antifreeze mask is not removed, and the instrument  is placed upside down, and the essence of Antifreeze Mask will flow into the instrument, causing the instrument to malfunction).

- After the operation,it may result in red spots, scars or rare bubbles.

- It’s recommended to operate for an hour

- It’s forbidden to erect work, please see (FIG. 7)

- When the machine is turned on, A1(appearing on the interface) indicates that the antifreeze mask is not installed, A2 indicates that the yellow filter cotton is wet, and A3 A4 indicates that the temperature of the frozen plate is too high

 

Application area of Frozen Body Shaping Instrument

 

Effect PictureOf Frozen Body-Shaping Instrument

 

Parameter of Frozen shaping body instrument

output voltage：DC12V/7A

Input voltage：100-240V

Output Power：90W

Cooling temperature：-2℃-12℃

Vacuum pressure：45 kpa maximum

setting time：30-99 min

Host size：21X16X8 CM

Host weight：1200 G

Size of Air box ：37X24X14 CM

Outer packaging size：40X30X18 CM ，Total weight:5 KG