Home > Products > Industrial Supplies > Machinery > Cleaning Machine

The trolley turntable sandblasting machine is a manual rotary table sandblasting machine, also known as mold sandblasting machine. It is suitable for sandblasting of heavy workpieces, with a load of 1000kg.

Working mode: connect the air pipe to the joint of the sandblasting machine, add sand, turn on the air compressor, turn on the power switch on the sandblasting machine, start the fan, step on the foot switch, pull the pressure regulating valve out, adjust the sandblasting pressure, turn right to increase the pressure, and turn left to adjust the pressure

After the pressure is adjusted, press down the knob of the pressure regulating valve, slowly add 5-8KG sand, and step on the foot switch to try spraying. Then buckle the turntable on the cart to prevent the turntable from sliding when loading the workpiece. Transport the workpiece to the turntable of the cart and push the cart to the sandblasting machine

At the entrance, the trolley rolling track should be aligned with the rolling track of the sandblasting cabin. Open the pull buckle of the fixed turntable on the cart, push the turntable and workpiece into the sandblasting processing cabin along with the rolling path of the cart, and then close the door of the processing cabin, turn on the power switch on the sandblasting machine, start the fan, and reach into the spray

In the rubber glove of sand processing hole, rotate the turntable, step on the foot switch, and hold the nozzle to sandblast the workpiece at the position where sandblasting is required. After sandblasting, release the foot switch, stop sand blasting, pull the turntable and workpiece out of the sandblasting processing cabin, and sandblasting is completed.

Note: please press the dust removal switch to remove the dust on the filter element every half an hour. Every 48 hours of work, it is necessary to clean the dust in the dust box. When sandblasting is not required for a long time, please turn off the power supply and air supply of the sandblasting machine.

Product Name: Wheeled turntable sandblasting machine mold sandblasting machine

Product model: hc1010tz

Overall dimension of main engine: 1600 * 1100 * 1800mm

Trolley size: 1200 * 1000 * 900mm

Working bin size: 1000 * 1000 * 850mm

Separator motor: 220 V / 50 Hz / 550 w

Dust removal method: filter element dedusting

Product Description:

1. The main body is made of 3mm steel plate, lined with 5mm anti-corrosion and wear-resistant rubber plate, which is durable, impact resistant and corrosion-resistant.

2. RS airbag pedal switch is used to control the equipment, which is safe and reliable.

3. The cyclone separator can separate dust and sand, design automatic sand return, recycle sand, reduce sand consumption and save product cost.

4. The machine has low noise, good sealing performance, dust blocking line of sight and no sand leakage.

5. Equipped with two-stage separator, it can better separate the dust, and further deal with the dust problem of the processing cabin, which can make the processing cabin more clear during processing, and further separate the available sand materials, which is suitable for all kinds of coarse and fine sand materials.

6. The body shape design is reasonable, the floor area is small, the performance is stable, and the wearing parts are few.

7. The pressure of sandblasting can be adjusted accurately by using pressure regulating and separating device.

8. Due to the need to process heavy workpieces, this sandblasting machine is equipped with a manual rotary table, which can rotate freely 360 degrees, which is convenient for sandblasting with multi angle and no dead angle. The rotary table can bear 1000kg.

9. The special rail cart design can lift heavy workpieces on the turntable, which is very convenient and labor-saving in and out of the processing cabin.

10. As heavy workpieces enter and exit the sandblasting chamber, this mold sandblasting machine is equipped with a cart, which can bear heavy workpieces within 2000kg, and can enter the sandblasting cabin for sandblasting treatment conveniently.

11. Explosion proof lamp, high life, multi protection, high brightness internal lighting system, providing sufficient brightness during sandblasting.

12. Gas source requirement: pressure 7 bar, flow rate 0.4-1.0 m3 / min.

The specifications of manual rotary table sandblasting machine can be customized according to customer requirements (the equipment in the picture is customized according to the size requirements of Russian customers)

This machine is suitable for some heat treatment molds, silicone molds, sole molds, plastic hardware molds, automobile accessories molds, engineering plastic molds, automobile wheel hubs and some heavy sheet metal parts, welding parts and frame components.