Home > Products > Industrial Supplies > Machinery > Machine Tool

Model: OKU-40T
Brand：Oreku Elbow Joint Punching Machine
Precision: JIS special grade
Speed: 1250 times/min
Tonnage: 40 tons
Stroke: 40mm

Crystal head chip precision terminal high-speed stamping automation equipment
1.Universal frequency converter + speed control shaft motor
2.Combined air pressure clutch brake
3.Dynamic balancing device (weight selective)
4. Electronic cam switch
5. Stop angle automatic correction device
6.Electronic crankshaft angle indicator gauge
7. Touch screen (Chinese: Simplified)
8.Speedometer
9.Total counter electronic 8 digits (touch screen)
10. Preset counter electronic 8-digit (touch screen)
11.Closed mold height display
12.Timer 7 digits
13.Motorized slide adjuster
14. Socket for misfeed (with switch) 1pc.
15.1 socket for stopping the tension limit
16.Micro inch movement
17.Circulating oil control unit
18.Air control unit
19.Material oil feeding device (with solenoid valve)
20.Safety door (front up/down type only)
21.Motor reversing device
22.Full stop circuit
23. Operating cabinet (with rolling wheels) body operating panel
24. Two-handed button (with 1-point CASE)
25.Oil cooling device
Optional accessories for precision leadframe high-speed punch press:
1.Anti-vibration device
2.Precision cam-clamp feeder
3. One material guide (to the working end surface)
4. Lower dead center detector
5. Cut-off counter (electronic 6-digit) 2 sets
6. Air injector (with solenoid valve) DC
7. Material drop hopper
8.Material end stop switch (proximity type)
9.Flywheel brake
Precision Lead Frame High Speed Punching Machine Parameters
Model: MARX-30T
Pressurizing capacity: 300KN
Stroke: 16/20/25/30 mm
Stroke number：200-1250/200-1200/200-1050/200-900 spm
Closed mold height: 190-240 mm
Slider adjustment: 50 mm
Slider size: 600×300 mm
Size of working table：600×400 mm
Table thickness: 90 mm
Table opening size: 400 (top) × 350 (bottom) × 60 mm
Table opening size: 400×100 mm
Main motor：11×4P kw
Upper mold weight：MAX80 kg
Total weight: 6500 kg
External dimensions：1780×3075×1210 mm
Crystal head chip precision terminal high-speed stamping automation equipment

Crystal head chip precision terminal high-speed stamping automation equipment

Crystal head chip precision terminal high-speed stamping automation equipment
 1, often keep the center column, the slider guide column clean, as well as racking the mold to keep the mold base plate free of dirt to ensure the cleanliness of the platform to avoid scratches. 2, the new machine in the use of 1 month, the flywheel at the addition of grease (including feeder), if the long time no refueling, will lead to internal wear and tear of the flywheel, affecting the performance of the machine tool, and then every time the maintenance needs to be added (high temperature 150 ℃ more than the grease) 
3, the replacement of machine circulating oil: new machine in 1 month to replace 1 time, and then every six months to replace 1 time, to ensure the normal operation of the machine tool and precision (32 # mechanical oil or Mobil 1405 #)
Precision lead frame high-speed punch press use
1, before starting the machine, the speed potentiometer (W) set on the control panel should be adjusted to the lowest point (O point) position.
2、After the main power switch (DK) is turned on, the power indicator light is on, and the phase sequence indicator light should also be on, otherwise the phase sequence should be checked to see if it is correct.
3、Break the phase after turning on the control circuit with the key switch. Indicator lamp three should be bright at the same time, otherwise should check, troubleshooting.
4, clockwise adjustment of the "speed" potentiometer, the main motor drive flywheel start, the speed should be smooth without vibration, no impact and other phenomena exist.
5, in the process of connecting the main clutch, should be operated at the same time left and right hand. In the process of formal stamping, the external control key switch should be turned on and the key switch of the regulator should be in the state of reset before it can work formally, otherwise the feeding switch and the mold failure signal will be out of control.
6、During the formal stamping process, since the static differential rate of the main motor varies with different loads, when stamping different parts, the electromagnetic register set on the control board can be used to correct the rotational speed.