Home > Products > Security & Protection > Alarm

1,GSM-Motocar connect map

1)ANT：controllor antanna

2)L-HIGHT：Left lamp,the other point of lamp connect to GND

3)R-HIGHT：Right lamp,the other point of lamp connect to GND

4)VDD：Power supply the base,connect to car 12V or 6V battery

5)GND：connect to car  battery ground

6)RESET：connect to GND to program the controllor into base ,or  RESET the base

7)LED：flash LED,the other end of the LED connect to GND,flash when alarm work.

8)LOCK：when the Motocar locked,lock input to the base is 12V or 6V,when unlock,it is 0V

9)AL：sound out,connect to siren, the other point of siren connect to GND

Output for stop the car,connect to ignition winding of the car

2,the use of the base

you can buy new GSM SIM card or you can use old SIM card,but you must delete all message and phone number.inset the SIM card into the base.

connect car battery(point 4 and point 5), The led of the base will bright on red in 20 second, then, it will flash yellow in 10 second, after that, it will flash green, this show the base work well. You can test the system. Flash LED (7) not work show the base in un-alarm state.if you set alarm state by controllor, Flash LED (7) will work.

In alarm state,you can first shake the Motocar,the base will sound 5 time“Bi”,if you shake second time in 20 second, the base will continuum sound out 40 time “Bi”, you shake thirdly in 20 second, the base will continuum sound out 40 time “Bi”and dial out the reprogram number,when you answer the base, you can monitor the voice in alarm place to hear what is happened.

3.program SMS and Phone to the base

you can send the message to the base :

123456#11# ，set the base start alarm state,the base will alarm when you shake it

123456#12# ，set the base end alarm state, the base will not alarm when you shake it

123456#13# ，set the base start sound out “Bi”,this time you need help

123456#22#123456#800000#，change code to 800000, next time you send the SMS,don’t forget new code.

123456#21#1# 13905950001#，set first group phone number:13905950001

123456#21#2# 13905950002#，set second group phone number:13905950002

123456#21#3# 13905950003#，set third group phone number:13905950003

To delede phone number:

123456#21#1##，To delede first group phone number

123456#21#2##，To delede second group phone number

123456#21#3##，To delede third group phone number

when you send this message to the base, the base will send the message return to you

4,how to use controllor

The remote controller has four buttons; button1, set alarm work；button2, set alarm off； button3, search for car, base sound out and Right /Left lamp flash；button4 (set shake sensitivity), If you push button4,the base sound out one time,the sensitivity is higher, If you push button4,the base sound out two time,the sensitivity is high, If you push button4,the base sound out three time,the sensitivity is middle, If you push button4,the base sound out four time,the sensitivity is low,

Note:

RESET：this point connect to GND for 1 second, the base sound out one “Bi”,at this time, you can program the controllor into base: when you push the button3 of controllor ,the base will sound a long “Bi” and flash red LED,

This show the controllor has set into the base. if you set RESET point connect to GND again or wait for 20 second,the base will retune normal use.

If RESET point connect to GND for 3 second,  the base will sound a long “Bi” and flash red LED,the base will delede all controllor and phone number saved in the base, and the code will be 123456