双轨劲拓无铅回流焊
| 型号： | JTR-800 |
|---|---|
| 品牌： | 劲拓 |
| 原产地： | 中国 |
| 类别： | 工业设备 / 环保设备 / 其他环保设备 |
| 标签︰ | 二手回流焊 , 劲拓回焊炉 , 劲拓回流焊 |
| 单价： |
¥98500
/ 台
|
| 最少订量： | 1 台 |
产品描述
| 回流焊参数 | ||||
| 型号 MODEL | VS-800II / NS-800II | VS-1000II / NS-1000II | VS-800IIX / NS-800IIX | VS-1000IIX / NS-1000IIX |
| 机体参数 GENERAL | ||||
| 外型尺寸(L*W*H) Outside Dimension(L*W*H) | 5310x1353x1490mm | 6100x1353x1490mm | 5310x1580x1490mm | 6100x1580x1490mm |
| 颜色 Standard Color | 计算机灰 Computer Grey | 计算机灰 Computer Grey | 计算机灰 Computer Grey | 计算机灰 Computer Grey |
| 重量 Weight | Approx.2250KG | Approx.2450KG | Approx.2350KG | Approx.2550KG |
| 加热区数量 Number Of Heating Zones | 上Up8/下Bottom8 | 上Up10/下Bottom10 | 上Up8/下Bottom8 | 上Up10/下Bottom10 |
| 加热区长度 Length Of Heating Zones | 3121mm | 3891mm | 3121mm | 3891mm |
| 冷却区数量 Number Of Cooling Zones | 2(内置) | |||
| 排风量要求 Exhaust Volume | 10 M3 / min x 2 (通道) Exhausts | |||
| 控制部分参数 Standard Feature Of Control System | ||||
| 电气要求 Electric Supply Required | 3 phase,380V 50/60Hz(optional: 3 phase,220V 50/60Hz 选配) | |||
| 电源功率要求 Electric Power Required | 64KW | 80KW | 64KW | 80KW |
| 启动功率 Power For Warm Up | 30KW | 36KW | 32KW | 38KW |
| 正常功率消耗 Power Consumption | 11KW | 13KW | 12KW | 14KW |
| 升温时间 Warming Time | 约 Approx.25 minute | 约 Approx.35 minute | ||
| 温度控制范围 Temp. Setting Range | 室温 Room Temp. --- 300℃ | |||
| 温度控制方式 Temperature Control Method | PID闭环控制 + SSR驱动 / PID Close Loop Control + SSR Driving | |||
| 温度控制精度 Temperature Control Precision | ± 1.0℃ | |||
| PCB板温分布偏差 Temperature Deviation on PCB | ± 1.5℃ (by JT Board Test Standard) | |||
| 加热器 Heating Element | Especial Heating elements For Long Life ; 特制的特长寿命加热器 | |||
| Commutated Element 整流板结构 | Aluminium Alloy Plate 铝板 | |||
| Max. Temp. Gap Between Preheat & Reflow Setting
预热区和焊接区之间的最大温度设定差值 |
80℃ | |||
| Max. Temp. Gap Between Preheat Zones Setting
预热区之间的最大温度设定差值 |
40℃ | |||
| Max. Temp. Gap Between Reflow Zones Setting
焊接区之间的最大温度设定差值 |
50℃ | |||
| 参数存储 Data Storage | 可存多种生产设置参数与状况 Process Data and Status Storage (80GB) | |||
| 异常报警 Abnormal Alarm | 温度异常（恒温后超高温或超低温）Abnormal Temperature (Extra-high / Extra-low Temp.) | |||
| 掉板报警 Board Dropped Alarm | 三色信号灯: 黄-升温；绿-恒温；红-异常 Tower Light: Yellow–Warming; Green-Normal; Red-Abnormal | |||
| 运输参数 Standard Features Of Conveyor System | ||||
| 导轨数量 | 1 Lane | 2 Lanes | ||
| Rail Structure 导轨结构 | Subsection Integrated Type 整体分段式 Subsection Separate Control分段独立控制(Option选配) | |||
| PCB最大宽度 Max.Width Of PCB | 400mm (Option:610mm 选项) | A and B lanes width each 250mm or 1 lane 450mm and other lane 50mm | ||
| 导轨调宽范围/调宽形式 | 50--400mm(Option:50--610mm 选项)/电动 Motorized | 50--450mm/电动 Motorized | (相关A、B线的宽度组合请参考上一栏) | |
| Range Of Rail Width/Adjustment | (Width relate to A&B, please refer item above) | |||
| 部品高度 Components Clearance | PCB板上/下各25mm , Top/ Bottom Clearance of PCB is 25mm | |||
| 运输方向 Converyor Direction | 左向右(选配: 右向左) L→R (Option: R→L) | |||
| 运输导轨固定方式 Fixed Rail Side | 前端固定(选配:后端固定)Front Rail Fixed(Option:Rear Rail Fixed) | 前后导轨固定，中央两条活动. Front and Rear Rails Fixed, 2 adjustable Rail at central. | ||
| PCB运输方式 PCB Transmission Agent | 空气炉 Air-Reflow = 链条+网带 Chain + Mesh , 氮气炉 N2-Reflow = 链条 Chain (可选配网带 Mesh is option) | |||
| 中央支撑 Center Support (选配 Option) | 防止PCB板因过宽及元器件过重而弯曲变形 Preventing PCB warp such too wide and heavy component load | |||
| 运输带高度 Converyor Height | 900±20mm | |||
| 运输速度 Converyor Speed Range | 300～2000mm/min | |||
| Lubrication Auto-Afflux 润滑油自动加注 | Standard | |||
| 回流热工学管理分析 Thermal Management System and Analysis System | ||||
| KIC RPI焊接质量检测系统 KIC RPI Reflow Process Inspection | 只标配于VS系列 , Standard for VS-series only | |||
| Temp. Thermocouple Slot
温度曲线测试线 |
4 | |||
| Electrical Driven Top Hood Opening
电动打开上温区盖 |
标准配置 Standard | |||
| Operation Mode: Operate / Demo / Edit
三种操作模式: 运行/演示/编辑 |
标准配置 Standard | |||
| On Line Editing 在线编辑功能 | 标准配置 Standard | |||
| Cooling Method 冷却方式 | Forced-Air 空气冷却 (标配Standard), Water-Chiller 冷水冷却(选配Option) | |||
| 带氮气系统机型 Model for Nitrogen Process | VS-800II-N / NS-800II-N | VS-1000II-N / NS-1000II-N | VS-800IIX-N / NS-800IIX-N | VS-1000IIX-N / NS-1000IIX-N |
| 电源功率要求 Electric Power Required | 67KW | 83KW | 67KW | 83KW |
| 启动功率 Power For Warm Up | 32KW | 38KW | 34KW | 40KW |
| 正常功率消耗 Power Consumption | 13KW | 15KW | 14KW | 16KW |
| 正常耗氮量 Nitrogen Consumption | 20M3/hr. @ 300ppm~1000ppm (O2浓度 / O2 Concentration) ; 氮气流量计 with N2 Flow Rate Meter | |||
| 助焊剂管理 Flux Management System | 氮气炉膛标配空气循环过滤，优化炉内环境，易于维护保养。Flux Reclaimed and Filtration standard for N2 Oven, easy clean-up. | |||
| N2 containment at Entry and Exit End
入口及出囗氮气保护装置 |
标准配置 Standard | |||
| Flux Reclaim System
助焊剂回收系统 |
标准配置 Standard | |||
| Nitrogen Flow Meter 氮气流量计 | 标准配置 Standard | |||
| Oxygen Analyser 氧气分析仪 | 选配 Option | |||
| Nitrogen Consumption [Standard]
氮气消耗量 (标准) |
400~1000PPM 20M³/H | |||
| Nitrogen consumption [Dilated hearth]
氮气消耗量 (加宽机) |
500~1000PPM 25~30M³/H | |||
| 冷水机 Water Chiller | 3 HP ; 外置式 External Stand-alone Type ; 充足冷却能力满足无铅工艺要求 Powerful Cooling suit to Lead-Free Process Required | |||
| 注明：氮气机在尾号为"-N"的设备才是标配 , Standard for N2 Oven Model With suffix of "-N" | ||||
| 付款方式︰ | 现金 |
|---|---|
| 交货期︰ | 一周 |
会员信息
| 深圳市伟圳联科技有限公司 | |
|---|---|
| 国家/地区︰ | 广东省深圳市 |
| 经营性质︰ | 生产商 |
| 联系电话︰ | 13823590218 |
| 联系人︰ | 范继仁 (协理) |
| 最后上线︰ | 2023/10/29 |