特点
Feature
*体积小,容量大,适合自动安装的卷(编)带包装。
Miniature size, large capacitance, tape and reel packaging suitable for auto-placement
*环氧树脂封装,从而具有优良的防潮性能、机械强度及耐热性。
Epoxy resin coating creates excellent performance in humidity resistance, mechanical strength and heat resistance
*工业生产标准尺寸及多种脚型产品。
Standard size, various lead configuration
介质种类
Dielectric Type
|
I类介质
Class I
|
II类介质
Class II
|
介质材料
Dielectric Material
|
温度补偿型
Temperature Compensating
|
X7R/X5R(B)
|
Z5U(E)
|
Y5V(Y/F)
|
电气性能
Electrical Properties
|
电气性能最稳定,几乎不随温度、电压和时间的变化而变化。
The electrical properties is the most stable one and has little change with temperature, voltage and time.
|
具有较高的介电常数,容量可做到比I类电容器高,具有稳定的温度特性。
X7R material has high dielectric constant, and its capacitance is higher than class I. These capacitors are classified as having a semi-stable T.C..
|
温度特性介于X7R和Y5V之间,容量稳定性相对较差,对温度、电压等条件较敏感。
Temperature characteristic is between that of X7R and Y5V. The capacitance is unstable and sensible to temperature and voltage.
|
介电常数最大,但温度特性较差,对温度、电压等条件较敏感。
Y5V material has highest dielectric constant. Its capacitance and dissipation is sensible to temperature and voltage.
|
应用
Application
|
适用于低损耗,稳定性要求高的高频电路,如滤波器、振动器和计时电路等。
Used in applications where low-losses and high-stability are required, such as filters, oscillators, and timing circuits so on.
|
适用于容量范围广,稳定性要求不高的电路中,如隔直、耦合、旁路及鉴频等电路中。
Used over a wide temperature range , such in these kinds of circuits, DC-blocking, coupling, bypassing, frequency discriminating etc.
|
适用于要求大容量,使用温度范围接近于室温的旁路、耦合等,及低直流偏压电路中。
Ideally suited for bypassing and coupling application circuits operating with low DC bias in the environment approaching to room temperature.
|
适用于要求大容量,温度变化不大的电路中
Used over a moderate temperature range in application where high capacitance is required.
|
容量范围
Available capacitance range
|
0.5pF~0.1uF
|
100pF~22uF
|
1nF~10uF
|
订货代码
Ordering Code
CT4 - 0805 Y 104 M 500 P F3
↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑
A B C D E F G H
尺寸、工作电压及容量关系表
Size Code and Voltage VS Capacitance
• 其它规格可直接和我们联系。
• Others are available, Contact yuexing.
通用型引线MLCC可靠性及测试方法
Reliability and Test Method for General Leaded MLCC
以上所示“标准条件”解释如下:
温度:5~35℃, 湿度:45~85%, 气压:86~106kPa
* Note on standard condition: " standard condition " referred to herein should be defined as follows:
5 to 35℃ of temperature, 45 to 75% of relative humidity, and 86 to 106kPa of atmospheric pressure.
若测试结果有争议时,仲裁试验用标准大气条件为:
温度:25±1℃, 相对湿度:48%~52%, 气压:86~106kPa
* When there are questions concerning measurement results:
In order to provide correlation data, the test should be conducted under a condition of 25 degrees plus/minus 1
centigrade of temperature, 48% through 52% of relative humidity and 86 through 106 kPa of atmospheric pressure.
包装形式
Packaging Style
注意Note:
P1=3.85mm for F=5.08mm;P1=5.1mm for F=2.54mm.
|