The DNP Standard color Viewer is a light source which enables you to evaluate and adjust video and still cameras. With its high-frequency Fluorescent lighting method, it handles images without flicker. |
|
|
|
Light source: |
DNP Standard color Viewer lamp
(Four 10W dedicated fluorescent tubes are used) |
Power supply: |
AC100V 50, 60Hz |
Lighting method: |
High Frequency lighting method 20KHz |
Color rendering: |
Over 90% rendering evaluation-point for each color |
Color temperature: |
(Measured by Minolta CL-200) |
Operating temperature: |
10~40℃ |
Operating humidity: |
Below 80%(avoid dew) |
Major diameter dimension: |
375W×365H×165D m/m |
Luminance plane dimension: |
250W×190H m/m |
Color chart dimension: |
320W×290H m/m |
Power consumption: |
80W |
Weight: |
6.5kg/7.5kg |
|
|
|
CCV-31F
CCV-51F |
|
|
CCV-31F/G
CCV-51F/G |
|
|
|
|
●The Luminance plane characteristics: according to the types of self-contained fluorescent lamp |
|
Product Type |
Luminance Color Temperature |
Lamp |
Color Temperature |
Luminance |
Color matching shift |
Weight |
CCV-31F |
Fixed |
FL10WW-DLB |
3100K±300 |
Over 1300cd/m2 |
Within 10% |
6.5kg |
CCV-51F |
Fixed |
FL10D-EDL-56K |
5100K±300 |
Over 1400cd/m2 |
Within 10% |
6.5kg |
CCV-31F/G |
Volume adjustable |
FL-10WW-DLB |
3100K±300 |
Over 850~1300cd/m2 |
Within 10% |
7.5kg |
CCV-51F/G |
Volume adjustable |
FL10D-EDL-56K |
5100K±300 |
Over 850~1400cd/m2 |
Within 10% |
7.5kg |
|
|
*The color temperature if Luminance. Color Temperature Conversion Type viewer ranges over 50k according to the change of the Luminance.
*The specification may change without notice |
|
|
|
【1】 |
Before using the product: |
|
|
Power supply |
|
AC 100V, 50/60Hz shared |
Light source |
|
10W DNP Standard color Viewer Lamp (4) |
Power consumption |
|
80W |
|
|
【2】 |
Using the DNP Standard color Viewer |
|
|
(1) |
Plug the power cable of the product into AC100V |
|
|
【Precautions】 |
Do not connect any power supply other than AC100V
If the other power supply connected by accident, the inverter inside will burned out |
|
|
(2) |
Turn on the power switch |
|
(3) |
Lamp lights: the lamp light will stabilised after 15 to 20 minutes at the room temperature(20℃) |
|
(4) |
If the lamp does not lit, call for Service Office for the confirmation as described on other documents. |
|
(5) |
To suspend snaking of the lamp, press power switch 3 to 4 times [as ON/OFF]. |
|
|
【3】 |
If the light does not lit |
|
|
Call for Service Office to confirm the following: |
|
(1) |
AC 100V supplied to the wall socket. |
|
(2) |
Plug the product into the wall socket. |
|
(3) |
Turn the power supply switch of the product ON |
|
|
|
|
|
|
Still the lamp does not lit: Consider the following: |
|
|
|
|
|
|
(1) |
Two of the viewer lamps lit simultaneously, one of the fuses of the inverters has blowouts. |
|
(2) |
Four of the viewer lamps does not light means that each of the fuses of the two inverters has blowouts. |
|
|
【Precautions】 |
The above occurs if the applied power supply is not AC 100V.
Fuse bum out cause internal burnout of inverter. The burned inverter needs to replace. |
|
|
|
【4】 |
How to replace the lamp and keep it clean |
|
|
Place the Viewer on the flat table, and plug out the power supply cable from the wall socket.
Remove the used device in the following order: |
|
(1) |
Unfasten the two of grub screws on the top frame. |
|
(2) |
To remove the top frame from the main unit;
Holding 50 to 60 mm the grub screw of the top frame and press it forward. |
|
(3) |
Remove the glass plate and acrylic plate. |
|
|
【Precaution】 |
Glass plate easily breaks and may hurt your hands and fingers.
Handle the edge of the plate with care not to scratch. |
|
|
|
◆Replacing the lamps: |
|
(1) |
When the lamps used over 2,000 hours or one year, it needs to replace. |
|
(2) |
Remove the Lamp Tubes: Hold the edge of the Lamp Tubes, and turn it 90 degree. |
|
|
◆Cleaning the device: |
|
(1) |
Impregnate alcohol to gauze then apply it onto the surface of the reflection plate / acrylic plate / glass surface to remove the dirt. |
|
(2) |
Clean the device once in six months to one year to keep quality of the Color Temperature and Luminance. |
|
|
【5】 |
Other Precautions |
|
|
Handling the viewer needs the following precautions because it contains the parts using glass. |
|
(1) |
Do not add strong impact on the viewer |
|
(2) |
Do not put any heavy items on the surface of the viewer |
|