DNH-A數控整流子點焊機

型號：	DNH-A
品牌：	HR
原產地：	中國
類別：	工業設備 / 其他工業設備
標籤︰	點焊機
單價：	-
最少訂量：	1 件

發送查詢

產品描述

DNH-A數控整流子點焊機

基本信息

該點焊機實用於汽車電機、電動工具和微電機等直流電機生產廠家焊接電樞引線到它的換向器。將一電樞放入定位座，對準焊接部位，啟動開關。機器將自動點焊和分度，直至電樞點焊完成並自動推出焊接完成的電樞，然後操作者移去電樞放入另一個電樞在定位座，又重新開始此循環。

技術參數

產品特點

1、適用於槽型，鉤型以及無槽形（兩根銅線與換向器之間）直接焊接。

2、能自動完成電樞夾緊，焊接轉位和退出的全套動作，自動化程序高，焊接質量好，效率高。

3、採用紅外溫度監控，形成全閉環控制，能精確控制焊點溫度，獲得高質量的均勻焊點。

4、能自動消除電源功能因素角及電壓波動變化的影響。

5、採用先進的焊接電流控制方法，大大提高了焊接變壓器有效輸出功率。

6、能按不同的工藝要求完成“自動焊接”、“單點焊接”、“保溫焊接”和“峰值焊接”。

7、焊接初始點火壓力連續可調，避免了電極與換向器接觸時的打火現象，顯著提高了焊點質量。

8、可預置參數自動補償前三點的焊接熱量。

9、配有兩套內部電控制系統，可單獨使用任意一套系統，兩套同時使用，再加間隔時間控制可自動完成高水平，“預熱-焊接”、“焊接-回火”等功能。

10、焊機系統均具有自我檢測及報警功能。

11、焊機分度裝置採用步進電機通過減速器帶動分度夾頭進行分度，由撥碼置數，電腦控制步進電機任意分度，使用非常方便。

12、焊機採用直線滾動導軌付導向，增加焊接時動作靈敏度及焊頭精確度。

13、焊機可裝150mm長焊頭（鎢極）進行焊接，大大延長了焊頭的使用壽命，同時也節約材料（鎢極）。

英文資料

DNH-A digital-controlled commutator spot welder

This welder can be used for the manufacturers of DC motors, such as automobile motors, electronic power tools, micro motor and etc., to weld armature leading wires to its commutator. Put the armature in the localization place, aim at the welding spot, turn on the switch, and then the machine will automatically weld the armature and calibrate the angles until all of the welding have been completed and the finished armature has automatically be pushed out. Then, the operator can remove the finished armature and put another one in the localization place; the new cycle will begin and so on.

This equipment has the following characteristic:

1, Suitable for the direct welding of the trough and hook as well as no trough (between the two cooper wires and commutator).

2. Able to automatically complete the entire operations of clamping armature, welding indexing and quitting; highly automatic routine, well welding quality, and high efficiency.

3.Using the infrared temperature monitoring to form entire closed-loop control, which can accurately control the temperature of the welding points, and obtain high quality and uniform welding points.

4. Able to automatically cancel the power factor angle and the affection of the voltage undulation.

5. Using the advanced control method of the welding current greatly enhances the effective output power of the welder transformer.

6. Able to complete the “automatic welding”, “single point welding”, “temperature preservation welding”, and “peak value welding”according to the different architecture requirements.

7. Continuous adjustment of the initial ignition pressure of welding avoids the striking light phenomenon when the electrode contacts the commutator, which greatly increases the welding quality.

8. Able to preset the parameters to automatically compensate the welding heat of the first three points.

9. Equip two sets of the internal electrical control system; may independently use any one of them, or use both of them at the same time; with the time interval control, be able to automatically complete the high level functions, such as “pre-heated welding”, “welding-tempering”, and etc..

10. Have the self-detecting and alarm-warning functions in the welder systems.

11. The angle calibration equipment adopts the stepper motor to drive the calibrating cartridge through the reduction gear to calibrate the angles.

12. The welders adopt the straight-line roll rails to guide the directions, which increases the welding moving sensitivity and the precision of the welding header.

13. The welder can adopt 150 mm welding header(tungstic electrode ) to weld, which greatly increases the life of the welding header and saves the materials(tungstic electrodes) .