盤配流液壓馬達
| 型號： | BM |
|---|---|
| 品牌： | 馬達 |
| 原產地： | 中國 |
| 類別： | 工業設備 / 礦業設備 |
| 標籤︰ | 液壓馬達 , 擺線馬達 , 盤配流馬達 |
| 單價： |
¥1200
/ 件
|
| 最少訂量： | 1 件 |
產品描述
BM6系列擺線液壓馬達
結構特點
BM6馬達是一種端面配流馬達。其結構特點：
•先進的端面配流設計,低速轉動平穩。
•先進的軸密封設計，能承受高背壓。
•先進的配油機構設計, 具有磨損自動補償功能。
•雙列圓錐滾子軸承設計能夠承受較大的徑向力。
•多種法蘭、輸出軸、等安裝連接形式。
BM6 motor is a disc valve type gerolor motor.
Characteristic features：
• Advanced design in disc distribution flow, which can provide improved performance at low speed.
•Advanced design of shaft seal, which can bear higher pressure.
•Advanced distribution mechanism design, which has the automatic compensation function.
•Double-rolling bearing design, which permit higher radial loads.
•A variety of connection types of flange; Rabbet:, output shaft and oil port.
主要性能參數 Main Specification
1.最大工作壓力指入口最大壓力，連續工作壓力指工作壓差.
2.馬達不能同時在最高壓力和最大轉速下工作.
3.在斷續工作條件下，運行時間每分鐘不得超過10%.
4.推薦用68#抗磨液壓油，粘度37-73cSt，清潔度ISO18/13.
5.最高工作油溫80°
6.馬達在滿負荷工作前，應在最高工作壓力的40%以下磨合1小時.
7.馬達允許最高背壓10MPa，但建議不要超過5MPa，超過時應接外泄油管.
1. Intermittent means the entrance of the maximum pressure; continuous working pressure means the differential pressure
2. Motor should not work under the highest pressure and the maximum speed
3. The running time should not exceed 10% under intermittent working conditions
4. Recommending N68 anti-wear hydraulic oil, viscosity 37-73cSt, cleanliness ISO18/13.
5. The Maximum working temperature is 80 °
6. One hour running time under 40% of maximum working pressure is recommended before full capacity working.
7. The maximum allowable back pressure is 10MPa, but the recommended back pressure should not exceed 5MPa.a leaking pipes is needed when exceeding
BM6 系列連接尺寸----外形及法蘭圖 Dimension and Mounting data
BM6 標準系列連接尺寸----輸出軸 Shaft
BM6標準系列連接尺寸----油口 Port
BM6訂貨信息 Ordering Information
BM6擺線馬達訂貨信息中選定型號及
會員信息
| 濟寧超越液壓機械有限公司 | |
|---|---|
| 國家/地區︰ | 山东省济宁市 |
| 經營性質︰ | 生產商 |
| 聯繫電話︰ | 13639449088 |
| 聯繫人︰ | 李慶彬 (經理) |
| 最後上線︰ | 2014/05/06 |
