型號: | FD-235HS 1211 |
---|---|
品牌: | TEAC |
原產地: | 菲律賓 |
類別: | 電腦、影音數碼 / 電腦配件 / 驅動器 |
標籤︰ | fd235hs1211 , 金鑲玉軟驅 , scsi軟驅 |
單價: |
US $900
/ 件
|
最少訂量: | 1 件 |
|
|
[金鑲玉集團]scsi軟驅 TEAC FD-235HS 1211
All TEAC models feature a 90-Days warranty from the date of purchase.
[金鑲玉集團]scsi軟驅 TEAC FD-235HS 1211
[金鑲玉集團]scsi軟驅 TEAC FD-235HS 1211
There is no need to register your product. TEAC provides 100% support for your product. You need, however, to keep your invoice in a safe place. The invoice is your proof of purchase and you will be required to send us a copy for repair and/or replacement.
[金鑲玉集團]scsi軟驅 TEAC FD-235HS 1211
[金鑲玉集團]scsi軟驅 TEAC FD-235HS 1211
Computer stores usually provide a 15 to 30-day warranty in most products. In case of a defective unit, contact your vendor immediately to have it replaced.
If your unit is out of warranty from the vendor, please contact our service department at xu@ruanqu.net for repair and/or replacement information, and have the following information ready:
Identifying your floppy Drive [金鑲玉集團]scsi軟驅 TEAC FD-235HS 1211 |
|
OEM production models are not listed in this knowledge base; you need to contact the manufacturer of the piece of equipment where your floppy drive was originally installed in order to receive information for repair, replacement, and availability. |
All TEAC 3.5 floppy disk drives have the prefix TEAC FD235HS-1111 scsi floppy drive, which denotes the size of the disk: 3.5 drive.
[金鑲玉集團]scsi軟驅 TEAC FD-235HS 1211
The next two characters in the model nomenclature denote the density, and type of interface of the device:
[金鑲玉集團]scsi軟驅 TEAC FD-235HS 1211
HS: Dual Density: 720K and 1.44MB; the letter S denotes the SCSI interface.
[金鑲玉集團]scsi軟驅 TEAC FD-235HS 1211
If your drive is not yet installed, you can identify it by its model label, which is located in the bottom side, towards the front side of the drive. Refer to figure A for details.
[金鑲玉集團]scsi軟驅 TEAC FD-235HS 1211
Figure A
[金鑲玉集團]scsi軟驅 TEAC FD-235HS 1211
Specifications |
|
The following table provides a description of the hardware specifications for the SCSI interface 3.5 1.44MB floppy disk drive models TEAC FD235HS-1111x.
[金鑲玉集團]scsi軟驅 TEAC FD-235HS 1211Model Name: |
711 |
911 |
1011 |
1111 |
Status: |
Discontinued |
Discontinued |
Discontinued |
Current |
Front Bezel: | Dark Beige (AT) | |||
Eject Button: | Dark Beige (AT) | |||
Internal Buffer: | 31KB | |||
LED Indicator: | Amber | |||
Interface Connector: | Standard 50-pin connector | |||
Signal Interface: | SCSI (Small Computer System Interface: ANSI standardX3.131-1986) | |||
Operation Mode Write / Read: | 2MB mode | 1MB mode | ||
Disk Used
(90mm / 3.5): |
High density (2HD) | Normal density (2DD) | ||
Data Transfer Rate: | 500KBps | 250KBps | ||
Unformatted Data Capacity: | 2MB | 1MB
|
||
Rotational Speed: | 300rpm | |||
Track Density: | 5.3 track/mm (135tpi) | |||
Track to Track Time: | 3ms | |||
Required Power: | +5V single (4.5V ~ 5.5V) | |||
Terminator: | 220 / 330 Ohm ?5% detachable (provided at factory) | |||
Specification of Parity: | ON at factory, ON / OFF switchable | |||
Specification of SCSI: | ID=0 at factory, switchable SCSI ID 0 to 7 | |||
Logical Unit Number: | LUN=0 at factory | |||
Dimensions: | 101.6 W X 33.3 H X 166 D mm | |||
Weight: | 480g | |||
Mounting: | Vertical/horizontal with spindle motor down | |||
MTBF: | 30,000 POH | |||
Safety Standards: | 1011, 1111: UL, CSA, TUV
711, 911: UL, CSA |
jumper information |
|
Figure A
[金鑲玉集團]scsi軟驅 TEAC FD-235HS 1211
a. |
SCSI ID Jumpers.
ID 0 by factory default. All jumpers ON. |
b. |
Power connector |
c. |
Standard floppy function jumpers. |
d. |
330 Ohm terminator |
e. |
Standard 50-pin SCSI interface |
f. |
Floppy bridge (34 to 50-pin connection) |
g. |
Floppy label** |
Figure B
Driver information
Although the TEAC FD235HS-1111 floppy drives have a standard SCSI interface, there are no drivers available from TEAC. You need to create your own drivers.
The process of development and implementation of software drivers is unique to each PC and NON-PC applications; and for that, the SCSI Command Set of Instructions is available at request to our Technical Support Department at DSPDTSG@TEAC.COM.
You are required to read, and sign our Non-Disclousure Agreement (NDA) and return it to us via fax: http://www.ruanqu.net . You should receive the manual upon approval.
Introduction
The quality of the TEAC FD235HS-1111 drives provide a trouble-free operation for your computer system if properly installed. The following information will guide you thoroughly through an easy step-by-step method for a proper installation of your floppy disk drive.
Your TEAC FD235HS-1111 drive must be handled with care. Avoid applying undue force or abnormal strain to the spindle motor, stepping motor or printed circuit board assembly (PCBA).
It is best to hold the drive by the sides. Never loosen the fixing screws of the PCBA.
Preparing your system
CAUTION: TURN OFF YOUR COMPUTER AND UNPLUG IT FROM THE AC POWER SOURCE BEFORE INSTALLING THE TEAC FD235HS-1111. FAILURE TO DO SO MAY RESULT IN ELECTRIC SHOCK.
1.
Unplug your computer.
2.
Detach all peripheral devices from your computer, such as printer, keyboard, mouse, etc.
3.
Remove cover from your computer. Refer to your computer manual for this procedure.
4.
The floppy interface cable is the flat ribbon type, and the power connector consists of the 4 separate wires attached to a single connector.
Configuring the TEAC FD235HS-1111 Floppy Disk Drive
1.
If this is the only device connected to your SCSI card, then make sure termination is enabled; otherwise, you need to verify that the drive's SCSI ID # does not conflict with any of the other devices connected to the chain; if the drive is not connected at the end of the chain, then you need to disable termination as well.
2.
Use a standard 50-pin SCSI interface cable to complete the installation.
3.
Connect the TEAC FD235HS-1111 floppy disk drive to the 50-pin SCSI cable.
Installing the TEAC FD235HS-1111 Floppy Disk Drive
1.
Slide the drive into the available standard 1 high bay.
2.
Locate the SCSI cable, and connect the red or blue stripe into pin # 1 in the drive, which is located towards the power connector in the drive.
3.
Connect the power connector to the drive.
4.
Place the screws through each set of holes in the drive.
5.
Be sure to have a copy of the SCSI Command Set manual so you can create your own drivers to make the interface possible between the TEAC FD235HS-1111 and your SCSI application. Refer to the Driver Information section for details.
Developers / System Integrators Documentation
TEAC America provides the following documentation for those customers in the United States of America, who are integrating the TEAC FD235HS-1111 drives into their hardware application design.
1. The Hardware specification manual includes information such as:
Physical dimensions
Reliability information (MTBF)
Environmental conditions
Power Interface and connectors
SCSI hardware interface (Pinouts)
Electrical characteristics
2. The Software specification manual includes detailed information on the command set supported by the TEAC drive.
3. Safety Agency Certificates may include UL, TUV, CE, CSA, etc.
金鑲玉集團有限公司 | |
---|---|
國家/地區︰ | 香港 特別行政區 |
經營性質︰ | 貿易商 |
聯繫電話︰ | 18663582868 |
聯繫人︰ | WELKIN XU (Manager) |
最後上線︰ | 2024/11/03 |