汽車座椅加熱系統 car seat heating system

一 綜合說明 General information

   此款產品是我們多年研究的結晶,在控制方面採用微電腦控制,溫度任意調節,同時有30分鐘定時功能.組成更為簡單,只有兩部分,由插到點煙器上的控制器和連體熱片組成.發熱部分採用高科技發熱材料,升溫快. This product is the result of our effort on researching and developing through many years, the control system is controlled by the micro-computer, the temperature is adjusting freely, with 30minutes timing function. The product is made by only two sections, the controller which is plug in to the cigarette-plug plus pads, the heating element is adopted by hi-tech heating material, with the character of temperature raising rapidly.

二 是您冬季的好伴侶 your best companion in winter season

   在每年寒冷的冬季,它升溫快,溫度任意調節,使您的腰酸腿疼有一定的緩解作用,對健康者-有一定的保健作用,可避免因寒風的入侵所引發的疼痛.in every cold winter, this product will reducing your painful of your waist and back through it’s rapidly temperature-raising and temperature-adjusting, it healthy to the people, to live away from the painful caused by cold wind.

三 安裝方法installation guide

  1.將座椅的外座套取下,而後將發熱片的背面雙面膠撕開,再將發熱片粘貼到座和靠背上,再把座套套好.貼熱片時座和靠背粘貼時要成直角take out the outer cover of the seat, tear off the double-side sticky, stick the heating pad into the bottom and back from the seat, then re-cover the seat cover, it should be a 90degree angle while sticking the bottom and back

  2.將加熱體的電極引出線從座和靠背的中縫處放于座椅下面.put the extend wire from electrode at the bottom of the seat where the position of the seat and back

  3.將溫度控制器插到汽車點煙器的插座中.而後將控制器的插頭和發熱體的插座在座椅下方對接,這時座椅加溫系統就安裝好了.plug the temperature controller into the cigarette-plug, to connect the connector of controller with the connector of the heating pads under the seat, then the whole heating system is installed well.

四 使用方法user’s manual

  1.將溫度控制器的開關從細的符號方向向粗符號方旋轉,這時電源燈和調溫燈同時亮,紅燈為升溫工作燈,綠燈為電源燈.turn the switch of the temperature controller from thin-sign to the thick-sign, the indicator of power and temperature-adjusting will be light-on at the same time, the red-indicator mean temperature raising indicator, the green-indicator means power indicator.

  2.調溫開關上的溫度指示符號越粗表示溫度越高.即向粗符號方向旋轉到某一位置不動后,表示把溫度設定在此點上.the changes of thicker-sign of temperature indicator from temperature adjusting switch means raising the temperature steadily, the temperature will be set up wile you turn the switch to the thicker-sign and stay in a certain position.

  3.如果在使用一段時間后發現溫度較高,這時可向細符號方向旋轉,將溫度設定低一些.if you feel the temperature is higher after you using it for a certain time, to reduce the set up temperature by turning the switch to the thinner-sign.

  4.如果要關掉加熱系統,只需將調溫開關旋到溫度調節符號最小處后即可,這時控制器上的燈全部滅掉.if you want switch off the heating system, just turn the temperature adjusting switch into the minimize of the sign, the indicator from the controller will be off at this time.

  5.具有定時功能:timing function

此控制器有30分鐘定時功能,到30分鐘后會自動關掉升溫系統,如果需要繼續使用,只需關了開關后再開一次即可.因為汽車有兩種功能的點煙器,一種是關閉發動機后點煙器上沒有電源輸出,另一種是關閉汽車發動機后點煙器上仍有電源輸出,這時如果忘關加溫系統,停放一夜后汽車電瓶的電會被用掉一部分,造成第二天早晨啟不着車.所以才設計了定時功能.this controller has the ability of timing with 30minutes, the system will be shut off the automatic temperature raising after 30minutes. If you want go on to use it, just switch off the switch and open it once again. This design is for that there are two functions of cigarette from the car: one is, there is no power on after switch off the engine. Another on is, there is still power on from the cigarette-plug after switch off the engine, for this kind of cigarette, if you forget to switch off the heating system, it will be consumed some power from car battery after one nigh parking, then it will cause the car starting trouble at the second morning, that’s the reason of this function desiged

五 注意事項attention

  1.控制器的點煙器插頭要和汽車上的點煙器插座要插接牢固.it should be a solid connection between the plug from controller with the cigarette-plug from the car

  2.發熱體要與汽車主駕駛的座和靠背粘貼牢固,並成直角.the heating pads should be stick solidly and in 90degree angle to the bottom and back from the seat of car driver

 

 

新產品介紹<五檔撥輪分控>

一 綜合說明

   此款產品是我們多年研究的結晶,在控制方面採用微電腦控制,溫度任意調節，組成更為簡單,只有兩部分,由控制器和連體熱片組成.發熱部分採用高科技發熱材料,升溫快.

二 是您冬季的好伴侶

   在每年寒冷的冬季,它升溫快,溫度任意調節,使您的腰酸腿疼有一定的緩解作用,對健康者有一定的保健作用,可避免因寒風的入侵所引發的疼痛.安裝后使您的車有了高檔車的享受。

三 安裝方法

  1.將座椅的外座套取下,而後將發熱片的背面雙面膠撕開,再將發熱片粘貼到座和靠背上,再把座套套好.貼熱片時座和靠背粘貼時要成直角.

  2.將加熱體的電極引出線從座和靠背的中縫處放于座椅下面.

  3.將溫度控制器插到汽車原預留孔中.而後將控制器的插頭和發熱體的插座在座椅下方對接,這時座椅加溫系統就安裝好了.

四 使用方法

  1.溫度控制器開關有三種：五檔撥輪，九檔撥輪，高低檔開關。將溫度控制器的開關從0，1，2，3，。。。的符號方向旋轉即為把溫度設在這些檔位。這時電源調溫燈同時亮,紅燈為升溫工作燈.

  2.調溫開關上的溫度指示符號越大表示溫度越高.即向數字大的符號方向旋轉到某一位置不動后,表示把溫度設定在此點上.

  3.如果在使用一段時間后發現溫度較高,這時可向數字小的方向旋轉,將溫度設定低一些.

  4.如果要關掉加熱系統,只需將調溫開關旋到溫度調節符號最小處“0”后即可,這時控制器上的燈全部滅掉.

  5．九檔開關的使用和五檔一樣。高低檔控溫時，只有兩檔，高檔和低檔。中間檔為關。

五 注意事項

  1.控制器的插頭要和線上的插頭要插接牢固.

  2.發熱體要與汽車主駕駛的座和靠背粘貼牢固,並成直角.

六．加熱片的規格：

46cmx46cm;46cmx26cm;40cmx40cm;開孔熱片，異形熱片，尺寸可按用戶要求生產。

七．功率：

20w,25w,30w,40w,45w,50w,55w,60w,65w,70w,75w,80w,85w,90w,95w,100w,110w,120w.

 八．配套：                 

   〈1〉。 我們已給國內外多家整車廠配套。〈2〉。是汽車美容，汽車裝飾，汽車維修，4s店首選產品。〈3〉。私家車也可方便安裝。             

  九：聯繫電電話 ：13021243672，010-81670268  ，朱先生。