時間控制：0-999ses

操作流程：
啟動電源開關，將溫度、時間、氣壓調至所需要求；
溫度達到時，請先試燙所需產品，將開關轉換至“手動”位置，確認試燙產品質量認可后方可轉換至“自動”位置批量生產；
當開關至“手動”位置時，用手按動“手動啟動”發熱板向下壓直至時間到后自動上升，如：燙印過程中發現位置不對，則按一下“緊急停止”中止燙壓，當開關至“自動”位置時，只需將發熱板推到位剛發熱板自動下壓。

注意事項：
整機必須有合適牢靠的地線保護。

維護事項：
氣壓：如壓力不夠或太大，可調氣瓶上調壓閥，向（+）方向加大壓力，向（—）方向減小壓力（請注意氣瓶是否有潤滑油）；
溫度：當設備到達設定溫度后發熱板不發熱或發熱不勻，請檢查溫控器接線同時確認熱電偶是否有損坏；
時間：當開關至“手動”時，按動“手動啟動”若不會下壓則檢查“手動”開關，當開關至“自動”時，台板到位時不會下壓，應檢查箱內微動開關接觸點是否到位，如不同位則應該調整；
如出現質量問題，請及時與本公司聯繫。

Product Description

Name:  Auto 4 table revolving printer   Model:GB-C3838  GB-C4050  ZS-C4060  GB-C6080 parameter:   Voltage:110v  220v  380v power:2250w Temperature range:0-399℃ Time range:0-180sec Air pressure:0-8kg Work table size:30*38 40*50 40*60 60*80 (cm) Casing size:105*80*160 160*80*160 170*80*160 (cm) Avoirdupois:150kg  160kg  170kg   Use: This machine can press sublimation, impregnant printing ink color picture on cotton, hemp, fibre and another fabric by heat press, it also can use in technics heat treatment as transplanting fur painting and froth printing. This aircraft electric appliance control uses the most vanguard technology, four revolving work the floor, the automatic spacing, the accurate security, the reliability is high, service life is long, electronic digit constant temperature control, precision high (±1-2℃). is your assembly line work best choice   Characteristic : 1. Using the most advanced control system, import element, auto fixing position , high capability for accuracy and safety ,long use lifetime . 2. PID Micro-computer controller .high precision ( 1℃) 3. Full digital time show, high accuracy 4. High quality import heat plate material . adopt with both air vacuum heating and oil heating devices maintaining consistent heat and strong heat exchange . 5. appearance is beautiful and fashionable   Operation:   1.      turn on the switch of power , adjust the temperature ,time and air pressure to the requirement . 2.      when temperature reaches the set point ,please print the test sample firstly ,adjust the switch to “ manual “ position, confirm the quality of test sample is passed , then can adjust the switch to “ automatic “ to produce as a batch when the switch was on “ manual “ position , please press the “ manual start” button ,the heating-plate will press down until the time is end then will automatic rise . eg: when find it is not the right position during the print process, should press “ urgent stop” button to stop print . when the switch is on “ automatic” position , just put the heating-plate to the right position then it can automatic press down. Notice : Must have a suitably and firm earth wire protection Maintenance:   1. air pressure : if the pressure is not enough or too much , you can loose or increase the pressure screw to adjust, turn to“ + ”for increase pressure , turn to “–” for loose pressure ( please note if has lube on the air-jar ) 2.temperature :when the temperature reaches to the set point while the heating-plate doesn’t work or heating not equality , please check if the temperature controller is turn on or circuit is destroyed. 3. time : when the switch turn on “ manual “ position  but can’t press down when press the “ manual start “ button , please check “manual” switch . when the switch turn on “ automatic “  the board reaches the position but can’t press down, please check the mirco- switch if connect correctly in the box , please adjust if not . 4. please contact us if have any quality problem