型號: | S227、S331 |
---|---|
品牌: | 勝鑫 |
原產地: | 中國 |
類別: | 工業設備 / 通用機械 / 焊接設備與材料 |
標籤︰ | 焊條 , 焊絲 , 錘頭 |
單價: |
¥1
/ 件
|
最少訂量: | 1 件 |
型號 | S227銅鋅焊絲 | 類型 | 實芯 |
品牌 | 勝鑫 | 助焊劑含量 | 6(%) |
標準直徑 | 1.0-5.0(mm) | 熔點 | 935(℃) |
重量 | 5(g) | 用途 | 熔點約935℃。高強度,釬焊鋼、鎳及硬質合金用 |
材質 | S227銅鋅焊絲 | 產地 | 河北 |
長度 | 400 | 工作溫度 | 930 |
規格 | 1.0-5.0 | 焊接電流 | 930 |
牌號 | S227銅鋅焊絲 | 是否含助焊劑 | 是 |
Category 類 別 |
Trade
牌 號 |
Chemical composition 主要成份(%) |
Characteristics & application 特性和用途 |
Equivalent to AWS 相當AWS |
Hardfacing 硬 面 堆 焊 |
S101耐磨焊絲 |
C3 Cr28 Ni4
|
HRc48-54. Resistance to wear, gas corrosion and oxidation. Hardfacing of bucket tooth and case pump.
|
|
S111鈷基焊絲 |
C1 Cr29 W5
|
HRc38-47. Resistance to wear and corrosion at high-temperature. Hardfacing of high temperature and pressure valve.
|
ECoCr-A |
|
S112鈷基焊絲 |
C1.5 Cr29 W8
|
HRc45-50. Resistance to wear and corrosion at high-temperature. Hardfacing of valve and hot-rolling pass.
|
ECoCr-B |
|
S113鈷基焊絲 |
C2.5 Cr30 W17
|
HRc≥55. Wear and heat resistance at high temperature, bad shock resistance. Hardfacing of screw charging carriage.
|
|
|
S114鈷基焊絲 |
C2.5 Cr30 W12
|
HRc≥53. Wear and heat resistance at high temperature, bad shock resistance. Hardfacing of three-cone bit.
|
ECoCr-C |
|
Copper alloys
銅
合
金 |
S201銅合金焊絲 |
Sn1 Si0.3Mn0.3
|
Good mechanical properties and crack resistance. Gas welding and argon arc welding of red copper.
|
ERCu |
S211銅合金焊絲 |
Si3 Mn1
|
Good mechanical properties. Argon arc welding of copper alloys and MIG brazing of steel.
|
ERCuSi-Al |
|
S212銅耐磨焊絲 |
Sn5 Cu Rem. |
Wear resistance. Argon arc welding of copper alloys and surfacing of steel.
|
ERCuSn-A |
|
S213銅耐磨焊絲 |
Sn8 Cu Rem. |
Wear resistance. Argon arc welding of copper alloys and surfacing of steel.
|
ERCuSn-C |
|
S214銅耐磨焊絲 |
Al7.5 Cu Rem. |
Wear and corrosion resistance. Argon arc welding of copper alloys and surfacing of steel.
|
ERCuAl-A1 |
|
S215銅耐磨焊絲 |
Al9 Cu Rem. |
Wear and corrosion resistance. Argon arc welding of copper alloys and surfacing of steel.
|
ERCuAl-A2 |
|
S221銅合金焊絲 |
Cu60 Sn1 Si0.3
|
Melting point is about 890℃. Gas welding and carbon arc welding of brass, also braze welding of copper, steel and cast iron.
|
|
|
S221F銅合金焊絲 |
Cu60 Sn1 Si 0.3
|
S221 welding rod coated with flux.
|
|
|
S222銅合金焊絲 |
Cu58Sn0.9Si0.1
|
Melting point is about 880℃. Gas welding and carbon arc welding of brass, also braze welding of copper, steel and cast iron.
|
RBCuZn-C |
|
S222F銅合金焊絲 |
Cu58Sn0.9Si0.1
|
S222 welding rod coated with flux.
|
RBCuZn-C |
|
S223銅合金焊絲 |
Cu59 Sn0.6
|
Melting point is about 900℃. Braze welding of copper, steel and cast iron.
|
RBCuZn-A |
|
S224銅鋅焊絲 |
Cu62 Si0.5
|
Melting point is about 905℃. Gas welding and carbon arc welding of brass, also braze welding of copper, steel and cast iron.
|
|
|
Copper
銅 合 金 |
S225銅鋅焊絲 |
Cu48 Ni10
|
Melting point is about 935℃ and high strength. Braze welding of steel, nickel and carbide alloys.
|
RBCuZn-D |
S225F銅鋅焊絲 |
Cu48 Ni10
|
S225 welding rod coated with flux.
|
RBCuZn-D |
|
S226銅鋅焊絲 |
Cu60 Sn0.3
|
Melting point is about 900℃. Gas welding of brass, also braze welding of copper, steel and cast iron.
|
|
|
S227銅鋅焊絲 |
Cu58Sn0.9Ni0.5
|
Melting point is about 880℃. Gas welding and carbon arc welding of brass, also braze welding of copper, steel and cast iron.
|
RBCuZn-B |
|
S229銅鋅焊絲 |
Cu55 Ni6 Mn4
|
Melting point is about 920℃, high strength. Braze welding of steel, nickel and hard carbide.
|
|
|
Aluminum alloys 鋁 合 金 |
S301純鋁焊絲 |
Al≥99.5 |
Good ductility and corrosion resistance. Gas welding and argon arc welding of pure aluminum.
|
ER1100 |
S311鋁鎂焊絲 |
Si5 Al Rem. |
Corrosion resistance, wide range of usage. Gas welding and argon arc welding of aluminum alloys other than high magnesium alloys.
|
ER4043 |
|
S321鋁焊絲 |
Mn1.3 Al Rem. |
Good corrosion resistance, weldability and ductility. Gas welding and argon arc welding of aluminum alloys.
|
|
|
S331鋁焊絲 |
Mg5 Mn0.4
|
Corrosion resistance and high strength. Argon arc welding of aluminum alloys.
|
ER5183< |
河北勝鑫(鑄造)焊接集團有限公司 | |
---|---|
國家/地區︰ | 河北省邢台市 |
經營性質︰ | 生產商 |
聯繫電話︰ | 18733947241 |
聯繫人︰ | 趙江濤 (經理) |
最後上線︰ | 2014/03/06 |