HDMI network matrix

24

Operation manual

The first chapter appearance description

1.1 front panel

The 1.2 panel

The 1.3 indicator light shows

The performance characteristics of the second chapter

The third chapter installation method

The fourth chapter hardware connection

The 4.1 switch to the network terminal equipment

The 4.2 switch to the network transmission equipment

The 4.3 power supply

The 4.4 device initialization

Check the installation of 4.5

The fifth chapter mode settings

5.1 the equipment login

The 5.2 network matrix input and output configuration

5.3 network matrix set

The 5.4 device user name password settings

5.5 equipment IP address

5.6 upgrade equipment

5.7 recovery equipment default settings

Appendix 1 technical specifications

The first chapter appearance description

1.1 front panel

Network matrix front panel provides 24 RJ45 ports, port LED indicating lamp, power indicator light and restore the default setting hole.

The 1.2 panel

A 220V exchange goods font socket, users in the installation, please insert the 220V AC power supply.

Note: for your use safety, please you the original configuration power cord use, safe and correct access plug wire board.

The 1.3 indicator light shows

Each port provides two lights: LINK/ACT and SPEED

> provide a power indicator

The performance characteristics of the second chapter

> all port 2 lightning protection and 16KV ESD protection, the uplink port No. 24 complete lightning protection

> 8K MAC address table, 4.8G backplane bandwidth, line speed forwarding

> built-in 100V-260V switching power supply, low power 4.5W, green energy-saving

The third chapter installation method

Network matrix installation is relatively simple, can be placed on the worktable network matrix smooth, please ensure that the table placed stably, and can withstand at least 1.5 kg weight, ensure that the power supply and switch the distance of not more than 1.5 meters. Network matrix when installed, casing around reserved 5-10CM gap, in order to ensure the required heat network matrix normal, network matrix surface to avoid placing other weight. Although the network matrix of all port 2 lightning protection and 16KV ESD protection design, but the large current of lightning to cause fatal damage to the network matrix components, so in order to better achieve the effect of lightning protection, please pay attention to the following matters.

> confirm the power socket and power to maintain good contact.

> reasonable wiring, avoid internal induction thunder.

The fourth chapter hardware connection

4.1 network matrix to HDMI TX and HDMI RX

All ports can be twisted and specify the HDMI network transmission equipment is connected, the maximum transmission distance of 100 meters.

The 4.2 power supply

Network matrix can use voltage of 100~260 volts, AC power frequency 50 ~ 60Hz. In the licensed operating voltage range, network matrix power will automatically according to the external power supply voltage is adjusted to ensure the stable operation, switch.

The 4.4 device initialization

After the power is switched on automatically initialized network matrix, so the network matrix indicating the following phenomena exhibit of lanterns:

> power indicator: Chang Liang said power supply connection is normal or abnormal, said power supply;

> other lights flickered: switch on the power off after, said system reset.

Check the installation of 4.5

Switch installed please check the following:

> check around network matrix if there is sufficient space for heat dissipation;

> power supply check network matrix with matrix network specifications;

> check all equipment is properly grounded;

> check matrix network and other network equipment is connected correctly.

The fifth chapter work settings

Network matrix can be flexibly according to the use of specific configuration of each port access to the HDMI TX or HDMI RX.

5.1 the equipment login

Network matrix default IP address: 192.168.168.254, user name: admin, password: admin, you need to use computer network matrix through the cable connector, the computer 's IP address changes and network matrix with the segment of the IP, the IE login 192.168.168.254, configure device.

Log on to the network matrix can be conveniently configured network matrix. When the user changes the forgotten network matrix configuration, please put in front of the restore default settings key long press 5-10 seconds, to restore the default setting of network matrix.

The 5.2 network matrix input and output configuration

In the Ports Tool Setting page can be configured to input or output and a name for each port. When the port is configured to correspond to the Input port need to contact HDMI TX, when the port is configured to correspond to the Output port must connect to HDMI RX

5.3 network matrix set

In the Ports Tool Port Config page for each output port according to the network matrix input and output configuration to display the HDMI TX.

The 5.4 device user name password settings

In the System tools User Manage page to change user password landing equipment.

5.5 equipment IP address

The change can be equipment IP address, device name System tools System config page.

5.6 upgrade equipment

In the System tools Upgrade Firmware page for device software update

5.7 recovery equipment default settings

In the System tools Restore Factory page to restore equipment factory setting.

Appendix 1 technical specifications

Parameters of content

Standards and protocols that support the IEEE802.3 10BASE-T Ethernet

100BASE-TX Fast Ethernet Support Agreement and standard IEEE802.3U

CSMA/CD Ethernet

The data transmission rate fast Ethernet 100Mbps half duplex, full duplex 200Mbps

The network media is 100BASE-TX:5 or above UTP/STP

The indicating lamp power indicator LINK/AC T and SPEED indicating lamp

Store and forward transmission mode

MAC address learning automatic updates, support 8K address space

Packet forwarding rate line speed forwarding

100~260V 50/60Hz 0.6A AC input power input

The working temperature of 0℃ ~40 ℃

The storage temperature of -40℃ ~70 ℃

Work humidity 10%~90% ( RH no condensation )

Storage humidity 5%~90% ( RH no condensation )

Size ( L * W * H ) 225 x 103 x 42 ( mm )