█ Summary
◆ The keyboard controller is used for terminal receivers such as the intelligent speed dome and the decoder
etc. It is very easy for operating and setting the speed dome camera. The controller is also to control the
terminal receiver to achieve the function of controlling pan/tilt, lens and etc.
◆ Taking the EIA/RS-485 electrical interface between the keyboard and the receiver.
◆ one keyboard can control as much as 32 speed dome and decoders.
◆ the maximum communication distance between the keyboard and the receiver is up to 1.2 km.
è Introduction of the keyboard Panel
The Sketch of the Front Panel and Description of Buttons (Figure 1)
Figure 1
1、CALL：To call the preset position.
2、PRESET：To set the preset position.
3、SHOT：To call cruising track.
4、F1：Auxiliary control buttons.
5、F2：Auxiliary control buttons.
6、F3：Switching control between intelligent speed dome and multiplexer.
7、WIDE：To a wide angle.
8、TELE：To turn to a telescopic range.
9、FAR：To make focus far manually.
10、NEAR：To make focus near manually.
11、CAM/ID：Select address of the intelligent Speed Dome.
12、AUTO：To control auto-horizontal rotation for pan/tilt.
13、OPEN：To open iris.
14、CLOSE：To close iris.
15、ON：Switch on the setting of function.
16、OFF：Switch off the setting of function.
17、FUNC：Set special function of the system together with other buttons.
18、PIP（up arrow）：Show picture of the camera in PIP mode (Picture-in-Picture).
19、FULL SCREEN：Show picture of the camera in full screen.
20、3×3（left arrow）：Show picture of the camera in 9-frame.
21、2×2（down arrow）：Show picture of the camera in 4-frame.
22、4×4（right arrow）：Show picture of the camera in 16-frame.
23、CLEAR： To clear inputted data.
24、0-9： Number key.
25、Enter：To confirm.
26、joystick：control the upward, downward, leftward and rightward speed motion of the speed dome.
27、Power LED
28、LCD
█ Rear Panel (Figure 2)

Figure 2
1、Power Switch: ON/OFF.
2、Power input connector: input DC12V power.
3、Communication connector RS485.
4、Communication connector RS485: twisted-pair.
5、Communication connector for DVR.
6、MODE：Used to set the protocol in use and the baud rate of communications.
7、Communication connector RS232.
█ Setting of the Keyboard
The protocol in use and the baud rate of communication of the keyboard are set by the MODE in
Figure 2. DIP1-DIP3 are used to select type of the communication protocol and the baud rate ,
shown as following table
◆ Some of the ID-Code of the protocols are set as follows:


◆ Switching control between speed dome and multiplexer：The controller can be operated in two
modes: Speed Dome and Multiplexer. When power supply is on it is operated on the default
mode, namely, the Speed Dome. Press [F3] to make switch between two modes. When it is under
the mode of the Multiplexer, you can control it via “Address Box”. At this time, the LCD will
display “Mulx Addr:001”. The RS-485 output of the keyboard cannot be used to control the
multiplexer. When operation, please pay attention to the information on the LCD.
Termination Resistor Setting
◆ The RS485standarda require a daisy-chain connection between the equipment. There
must be termination resistor with 120 ohms impedance at both ends of the connection
(refer to the following FIGURE):

◆ Setting termination resistor by the DIP5 of the MODE as follows:


█ Operation of the Keyboard
1. Select Address of the Speed Dome Camera：[CAM]+[N]+[Enter]
Display: Current CamID：001
Description：N –– No. of camera from 0 to 255
Function：Select the address of the camera to be controlled. When the value N is in conformity with the address of the Speed Dome Camera, it will be under control.
2. Set the Preset Position：[PRESET]+[N]+[ Enter]
Display：Preset No：001
Description：N –– No. of preset position from 1 to 255.
Function：Store current position and refer it as No. N position.
3. Call the Preset Position：[CALL]+[N]+[ Enter]
Display：Call Number：001
Description:：N –– No. of preset position from 1 to 255.
Function： Transfer the camera to the position of No. N preset position.
4. Cancel the Preset Position:[PRESET]+[N]+[OFF]
Display：Preset No：001
Description：N –– No. of preset position from 1 to 255.
Function：Delete the No. N preset position stored.
5. Set the Cruise Track (COP-2, PELCO-D, PELCO-P Available)：
◆ Enter the Status of Track Setting：[SHOT]+[N]+ [ON] (N：No. of track from 1 to 6).
Display：Track = 01 Sum = 06
Description：Track No.1 is currently setting, in which there are 6 preset points.
◆ Edit Track：Press [TELE] to edit down page and press [WIDE] to edit up page. Each track involves 16 preset
points and the running speed and the dwelling time of each preset position.
Display：No.：01 Point：001 → Description：The 1st preset position in the track is 001.
Display：No.：01 Speed：001 → Description：The speed of the 1st preset point in the track is the 1st class.
Display：No.：01 Time： 004 → Description：The dwelling time of the 1st preset point in the track is 4
Seconds
◆ Speed Range：1 to 8 from the fastest to the lowest. Any speed outside the range will be referred as the 1st
class; the range of the dwelling time is：1 to 255.
◆ When the No. N preset point is set as No. 0, then all preset points before the No. N preset point in the track
will be valid however all numbers of preset points afterward and their speed and dwelling time shall be set as
0 automatically.
◆ After tracks are edited, press OFF to store and exit while push the joystick to exit without storage.
6. Run Cruise Track: [SHOT]+[N]+ [Enter]
Display：Input Tour No：01
Description：N –– No. of the track from 1 to 6.
Function：Tour the No. N track and stop tour by pushing the joystick.
7. Stop Cruise Track: [SHOT]+[N]+ [OFF]
Display：Input Tour No：01
Description：N –– No. of the track from 1 to 6.
Function：Stop the No. N track or stop tour by pushing the joystick.
8. Cancel Cruise Track: [SHOT]+[N]+ [OFF] (Pressing [OFF] down until “ Clear Tour OK ”appears)
Display：Input Tour No：01
Description：N –– No. of the track from 1 to 6.
Function：Delete the No. N track
9. Auto Pan ON (Operation of COP-2 Protocol): [AUTO]+[P1]+[ON]+[P2]+[OFF]
Display：Input 1st No：001
Description：P1–––– the starting scan No. of preset point from 1 to 255, which should be set already.
Display：Input 2nd No：002
Description：P2–––– the ending scan No. of preset point from 1 to 255, which should be set already.
If P1 = P2 or P1 and P2 are coincided, the speed dome will make scan in range of 360°.
Note:
(1) For PELCO-D and PELCO-P Protocols the way of operation is as follows:
◆ Set the Starting Scan Position: Transfer the speed dome to the starting scan position, operation
[AUTO]+[ON]
◆ Set the Ending Scan Position: Transfer the speed dome to the ending scan position, operation
[AUTO]+[OFF]
◆ Run Auto Pan：[AUTO]+[ENTER]
(2) Auto Pan operation takes the following parameters. You must set these parameters before using a
Auto Pan command to begin the scan operation. You can use the scan Stop command or PT scan stop
command to stop the scan. Setting scan condition:
◆ Auto Pan Position(First specify position, second specify position)
◆ Auto Pan Speed and Direction.
10. Stop Auto Pan：[AUTO]+[OFF] (only for COP-2 protocol)or push the joystick to stop scan.
11. Control the Zoom of the Camera：[WIDE]/[TELE]
12. Control the Focus of the Camera：[FAR]/[NEAR]
13. Control the Iris of the Camera：[OPEN]/[CLOSE]
14. Control the Vibration Correction of the Camera：[ON]/[OFF]
15. Auxiliary Control of the Camera： By combination of [F1] and [ON], [OFF] buttons, you can set some data of the camera, and functions are listed as follows：

16. Use the Joystick to control the speed dome camera：
You can use the speed joystick to control the Pan/Tilt direction and speed of the speed dome randomly. The speed
of pan/tilt is decided by the angle of the joystick you operated (Figure 3).
Change the tilting angle of the joystick you can adjust the speed evenly and the camera can be focused automatically
in the course of scan to keep images being distinct.
Figure 3
█ Installation and Connection:
Attention： Please read the operation manual of the keyboard and the speed dome carefully before connecting wires. Any incorrect connections can cause permanent damage of the device. When connecting wires, first switch off the power supply of all devices. The communication wires between devices should be shielded twisted cable. When installing cables they should be far away from high voltage lines or other possible interference circuits as can as possible.
1. The marking of wires of the transfer box (Figure 4)
2. Connections of the keyboard controller controlling multiple speed dome cameras (Figure 5)
3. Connections between the keyboard and the speed dome camera (Figure 6)
4. Connection Drawing between the keyboard and the multiplexer via the address box (Figure 7)
5. System Connection Drawing between the keyboard and the dome camera and the multiplexer (Figure 8)


█ Technical Specifications：
◆ Communication between Speed Dome Camera and Controller：Port to multi-port and half duplex function.
◆ Communication connector: RS-485.
◆ Baud Rate of Communication：Four baud rates i.e. 2400bps, 4800bps and 9600bps.
◆ Distance of Communication：1200m in maximum
◆ Power Supply：DC12V/1A ; Over voltage 14.5V±0.5V.
◆ Size：330 × 190 × 43（mm）
◆ Weight：1.62 Kg
◆ Number of controlled speed dome camera up to 128.
█ Points for Attention：
◆ Please read the operation manual of the keyboard carefully before using it.
◆The keyboard takes DC12V power supply. Please confirm the voltage and polarity before the power supply is
switched on.
◆ Do not place the keyboard under the rain or on wet place so as to avoid short circuit or electrical shock.
◆ As the keyboard is a sophisticated electronic device, you should never open the case so as to avoid the
occurrence of trouble.
◆ The keyboard has integrated multiple protocols, and you are pleased to select correct protocol and the baud rate.
When switching on power supply, take care of the selected protocol and the baud rate on the first screen.
█ Packing List
◆ Keyboard 1
◆ Power Adapter 1