Reasonable factory price mini incubator YZ8-48  

I.Compared with the JN8-48,Our YZ8-48 have following advantages:

1. It's transparent for you to see all the process of hatching ,  also very good for children's eudcation purpose .
2. you can add water outside of the mahcine With our tool, no need you to open it  .
3. We have improved the controller, it can be in the better condition instead of the old one of JN8-48.
4. We have changed the fan ,which can have lower noise when working , better for the circulation of temperature and improvement of hatching rate .
5. Temperature heating element is changed to be a new improved one . when the temperature is higher , the heater will be stopped to avoid self-ignite , It's better to keep ideal temperature inside the machine .
6. Very competitive price with high quality ,  only 70USD per pcs (instead of more than 100USD for old JN8-48 on the market .)

 

II. Display Symbols

 III.Basic operation

1. Testing you unit for the first time:

1.1 Connect the egg turner plug to the control plug inside the egg compartment.

1.2 Connect the provided power supply to the back of the unit and your power source.

1.3 Switch on your power source.

1.4 Switch your unit on.

1.5 You will hear an alarm sounding due to low temperature/humidity.

1.6 Press any of the green buttons to cancel the alarm.

1.7 By opening the incubator and filling the water channels you will notice the humidity reading increase.

1.8 Let the unit run for 2 hours to note the egg turner turning.

 

2. Setting the temperature

2.1 Push “SET” once.

2.2 Push “+” or “-“ to select the desired temperature.

2.3 Push “SET” once more to exit.
These incubators are factory set at 38^oC, I found the chicks hatch at day 19 to

20 meaning the temperature being to high. Using the method as described

above. I recommend you set the temperature at 37.6^oC.

3. Temperature alarm parameter settings (AL and AH)

The temperature alarm is factory set to sound at 1^oC over or below the set temperature. This is sufficient and you do not need to make any changes to these settings.

3.1 Low temperature alarm parameter setting. (AL)

3.1.1 Press and hold “SETT” for 3 sec.

3.1.2 Push “+” or “-“ until code “AL” appears in the temperature screen.

3.1.3 Push “SET”

3.1.4 Push “+” or “-“ to adjust to your desired lower alarm setting.

3.2 Higher temperature alarm parameter setting (AH)

3.2.1 Press and hold “SETT” for 3 sec.

3.2.2 Push “+” or “-“ until code “AH” appears in the temperature screen.

3.2.3 Push “SET”

3.2.4 Push “+” or “-“ to adjust to your desired higher alarm setting.

 

4. Humidity alarm parameter settings (AS)

The humidity alarm is factory set to sound at 45% humidity. This is sufficient and you should not deed to make any changes to these settings.

4.1 Low humidity alarm parameter setting. (AS)

4.2 Press and hold “SETT” for 3 sec.

4.3 Push “+” or “-“ until code “AS” appears in the temperature screen.

4.4 Push “SET”

4.5 Push “+” or “-“ to adjust to your desired lower alarm setting.

By filling both water channels the humidity should rise to 60% dependant on the

local humidity levels and the time of year. I tend to fill both my water channels

every 4 to 5 days and at day 18 when I remove the egg trays I over fill them to

increase the humidity to about 65%.

IV.Package

2 pcs/big carton,

packing size is 52x60x53/15kgs/2set.

 

V. The pictures for your reference

 

 

 

The single piece package:

The whole package for 2 sets