Technical parameters 

1. Working pressure: 0.05Mpa-1Mpa. 
2. The ideal pressure: 0.1Mpa-0.5Mpa, 0.5MPa to install valve over. 
3. Standard pressure: dynamic pressure 0.3 ± 0.02Mpa. 
4. Cold water temperature: 4-29 centigrade, hot water temperature: 55-85 centigrade, the normal recommended use temperature is 60-70 centigrade. 
5. Thermostatic water temperature: 20-50 centigrade. 
6. Safety button set temperature: 38 centigrade. 
7. Temperature accuracy: first set the desired temperature, the water can be achieved within 5s after your desired temperature, the temperature 
8. Degree of volatility within the ± 1 centigrade. 
9. Water temperature stability: When the water temperature constant, cold, hot water pressure 50% of any change, water temperature fluctuations 
10.  Within the ± 2 centigrade; when the water pressure constant hot water temperature from 60 centigrade rise 75 centigrade (5 centigrade / min), the 
11. Fluctuations in water temperature within ± 2 centigrade. 
12. Applicable standards: ASME A112.18.1-2005/CSA B125.1-05, ASSE1016 EN1111, 
     AS-4032.1 and QB2806-2006 and so on.

This thermostatic valve pipe valve, cold, hot water interface is 4 "with H labeled water interface, the C labeled cold water interface", mixed water interface, the interface is 4 points. 
  
Thermostatic mixing valve Britain Bo built-in temperature sensor unit, the temperature of the media installed in the valve body at the mixing section, mixing with the temperature sensor and, based on the mixing valve temperature setting, drive spool to automatically adjust the mixing ratio of hot and cold water, thus providing accurate temperature control. Ultisolar series thermostatic mixing valve applications unique thermal media, which greatly improves the life and speed of response. 
  
Ease of use 
By adjusting the valve on the handle to set the required mixing temperature. Under normal circumstances no maintenance, even when in need of repair, O-ring, the sensor unit and the spool and other components can be easily disassembled. 
  
Designed to balance the pressure of the water system can be implemented after the rapid stabilization of the temperature to set the temperature effect, after the change in pressure will be a great deviation, far below the normal pressure of publicity in the hot and cold water than the "9:1" goal. 
  
* Safety anti-scald 
Thermostatic mixing valve safety-critical. Such as cold water failure, the valve must be closed hot water at breakneck speed, reaction time is too long will burn incident occurred, if there is no such function, the valve cannot be used. Hot water failure, the valve should also be at great speed off in cold water, or can also cause skin irritation. 

When the cold water supply of a sudden interruption of water temperature higher than the set temperature, the thermostatic mixing valve can be closed quickly in 2 seconds of hot water supply, in order to avoid scalding hot water, the reaction rate is much higher than similar products at home and abroad, really does to foolproof. And when a sudden interruption of cold water supply temperature is below the set temperature, the thermostatic mixing valve can be closed quickly in 2 seconds of cold water supply to prevent the chilling phenomenon. 
  
* Applications 
1, Bo Ying thermostatic mixing valve can be used in solar water heaters, water heaters and gas water heater the water heater temperature control system, anti-hot temperature. 
  
2, cooling anti-scald, thermostatic mixing valve Britain Bo can be applied in the home, hotels, hospitals and other independent or centralized hot water system, to automatically mix hot and cold water and keep mixing temperature stability (more than for the DN20 ). 
  
3, thermostatic mixing valve can be used to improve heat source (such as solar water heaters) and water efficiency, relying on mixed with cold water to control water temperature, increase hot water flow, water heater can greatly reduce the user capacity.