Model: | 603010022 |
---|---|
Brand: | Autol |
Origin: | Made In China |
Category: | Transportation / Car Accessories / Auto Repair Tools |
Label: | Tango Key Programmer , Tango Programmer , Tango Key Tool |
Price: |
-
|
Min. Order: | 1 pc |
Tango Key Programmer With Basic Software
Attention: After generating a new transponder with TANGO Programmer, you will not need any additional
diagnostic equipment to program the generated transponder to the car!
It will start the car directly, even on new FIAT CODE 2 system, also used in PSA Group vehicles! Only you have
to write the new file back into the immobilizer system!
List of Supported Transponders :
Philips Transponders:
PCF7930-31 writing, reading
PCF7935 writing, reading, shadow memory, crypto calculator
PCF7936 writing, reading, modes password, crypto, Manchester & Biphase encodings
PCF7941 transponder, remote, eeprom, Manchester & Biphase encodings
PCF7942 transponder, remote, eeprom, Manchester & Biphase encodings
PCF7943 transponder, remote, Manchester & Biphase encodings
PCF7944 transponder, remote, eeprom, Manchester & Biphase encodings
PCF7945 transponder, remote, eeprom, Manchester & Biphase encodings
PCF7946 transponder, remote, Manchester & Biphase encodings
PCF7947 transponder, remote, eeprom, Manchester & Biphase encodings
PCF7952 transponder, remote, eeprom, Manchester & Biphase encodings
PCF7961 transponder, remote, Manchester & Biphase encodings
Auto switching between PCF7936-PCF7961 windows if invalid type detected.
Autodetect manchester / biphase
Temic Transponders:
Temic 11 reading , writing to T5
Temic 12 reading , writing to T5
Megamos Transponders:
Megamos (13) reading , writing to T5 , emulating on PCF7930-35
Megamos (48) reading, writing, PIN, unlock by PIN, full range of memory contents, crypto calculation
Megamos CRYPTO-2 (8E) read ID, read/write EEPROM, write Cryptokey
Texas Transponders:
Tiris (4C) reading
Tiris (4D) DST crypto reading, writing, crypto calculator
Tiris (4E) DST crypto reading, writing, crypto calculator
Tiris (8C) reading
Atmel:
TK5551M (T5 replacement)
SAAB reading , writing to T5
The product is in working out stages, therefore the list of the supported transponders will be developed later.
Key Maker Usage.
Key maker usage consists of a four steps. The 4-th step is additional and depends on a vehicle model.
1. Open an immobilizer dump file.
2. Choose number of the key you want create.
3. Place a transponder into the coil and click the WRITE button.
4. In some cases the program asks you to save a modified immobilizer dump.
This dump must to be written into the immobilizer.
First of all, take a look at this picture. The "Loaded File" window displays the immobilizer file name. Ensure that a valid dump is stored.
The "Maker"window displays selected maker name. Ensure the right key maker selected.
The "info" windows display an important information:
1. Original transponder---Informs you about type of the original transponder
2. Allowed transponder---Informs you what type of transponders is suitable for the key maker
3. Data location------- The immobilizer memory may be stored in various chips, the description informs you about from where you have
to read a dump.
Some immobilizers can have various chipsets. In this case the field displays several possible chips. Find one of
them inside of the immobilizer and read it.
4. Data size---Each chip has certain memory size, the key maker accepts files with the described size.
5. Data format---This field appears in case of 93CXX eeprom seria.
There are two standards of data layout:
Intel format and Motorola format or Little Endian and Big Endian respectively.
The data layout depends on a chip-programmer that is used for eeprom reading.This field informs you what kind of format is suitable for the key maker.Usually you can see that both
formats are suitable. It means that the program can understand any data layout.
Create a key step by step
Firstly, run the key maker interface according to the vehicle and read information in the "Info" window. Watch theData location field describes the
memory chip. Find out the chip inside of the immobilizer and read it. Save the read data (dump).
Click the "OPEN IMMOBILIZER FILE" button and load the saved dump.
The program will analyse the dump.
If the dump is correct the "WRITE" button will become active and the "Keys" window will display the range of key numbers that can be created.
Take a look at the "Info" window, the Allowed transponder field.
Ensure you use a transponder exactly the indicated type.
Place the transponder into the coil.
Choose the key position you want create in the "Keys" window.
Click the "WRITE" button.
This starts the writing process and transponder will be stored with the appropriate data.
At this point you may be asked to save a new immobilizer dump.
The program displays a standard File Save dialog where you have to save the data.
After this you will be informed about the new data saved and must be written into the immobiliser.
Write the new dump into the immobilizer. Now it is ready to operate with the created transponder.
If you are not asked to save a new file, it means that immobilizer is ready to operate with the created transponder without file replacing.
Finish.
1. ABS plastic enclosure:
ingress protection
IP65/DIN EN 60529
2. Rubber seal:
prevents sliding on a workbench
shock-proof function
3. USB connection:
no external power
4. Big hole:
adopted to large keys
5. Three small holes:
adopted to various sizes of transponders
Very Important Tips:
We have much experience on customs clearing,
Please tell us what is the best price for you for declared value of the package, so that you avoid paying high tax.
As is known to all, France and Turkeyhave strict import policy.
so if your package is going to these countries, you must quite familiar with the policy and tell us what is the best.
If you are from Brazil,you must provide your CPF Number (TAX Number).
Customers from Hungary,Turkey,Brazil,Belarus,Russia,you`d better choose EMS Shipping Method
If you not get the package due to the policy in your country, We will not bear the lost
Hope to you understand.
Promised by Supplier
(1)Guarantee: one year, from the date equipment arrival
(2)We will provide technical support for free by Phone or Internet
All of our products come directly from factory, they are 100% Brand New and in perfect condition.
We will deliver your package within 24 hours as soon as we confirm your full payment.
DHL: 3-5business days
UPS: 3-5 buisness days
EMS: 5-10 business days
HK Normal post: 15-30 business days
After we make the shipment, we will tell you the shipping information as well as the tracking number.
We will track it for you. And you can also track it online.
Note: We hope it arrive on time but since this is an international delivery, shipping time will be highly depended
on the company and local customs. Thank you for your understanding.
1.If you receive a wrong or defective item, please Email us within 3 working days from the date you receive the
items.We will tell you the exact process of the return.
2. If there is any problems with the products you buy, we`ll make an exchange or refund the product payment
(shipping&handling fees are not included) within 30 days after confirm receipt of the goods.
3. The shipping and handling charge is not refundable and customer should be responsible for all the
charges of returning and reshipping. All return items must be in good condition.
If you are satisfied with our products,please leave us positive feedbacks----5 Stars
Thanks for your supporting
sherry
email:sherry at autoltech dot com
slype:autolsale008
Sherry-Autol Technology Co., Limited | |
---|---|
Country/Region: | Guang Dong - China |
Business Nature: | Trading Company |
Phone: | 889614 |
Contact: | sherry (auto) |
Last Online: | 25 Jun, 2014 |