Advantage of our carbide products:

1) made from 100% raw virgin material

2) More than 10 years production experience

3) Advanced equipments

4)All products go through process and final inspection

5) All size available

6)Small/Trail order accepted

Products information:

Special shaped tungsten carbide nozzle from zhuzhou hongtong.

Our nozzles are built to speed the flow of gases, liquids and slurries of virtually any viscosity and to withstand punishing wear, erosion and/or chemical attack in harsh chemical and powder service environments. They have proved to be a high performance, long-lasting alternative to hard steel.

For nozzles, tungsten Carbide nozzle is the most r ed and durable and provides the best value.

A nozzle is a device designed to control the direction or characteristics of a flow (especially to increase velocity) as it exits (or enters) an enclosed chamber or pipe via an orifice. For nozzles, tungsten Carbide nozzle is the most r ed and durable and provides the best value.

Tungsten carbide nozzle is made by the precision machining with the tungsten carbide materials (superhard alloy). The hardness reached over HRA90 degree while the anti-bending degree reached over 2300N/mm2. On machining tungsten carbide nozzle, we do the precision grinding and surface treatment to achieve Ra0.1 of the bore roughness and the Ra0.025 of the R place of both ends. There is a scientific curvature radius design in the both entrance. This design can ensure a smooth transit of the thread. Due to the overall materials processing, and no elevation in the bore, the phenomenon of easy-bending and pl ing has been improved comparing with the ruby nozzle.

Tungsten carbide nozzle is made from hot pressing with straight bore and venturi bore type. Due to its hardness, low density and excellent wear and anti-corrosion, Tungsten carbide nozzle has been widely used in sandblasting and shot peening equipment, offering a long life with optimum air and abrasive use.

How to choose a tungsten carbide nozzle?

When choosing a tungsten carbide nozzle, consider the amount of available air in cfm, the capacity of the blast machine and the inside diameter of the piping, and the blast and air hoses. For optimal performance, these elements must be compatibly sized.

If too large a nozzle is used, low blast pressure and rapid wear on the blast hose will occur. If too small a nozzle is used, smooth media flow will be difficult to achieve.

Grades and Applicaton recommended:

Grade	Equivalent	Density	HRA	T.R.S	Application
	To ISO	(g/cm3)		(Mpa)
YG3X	K05	14.9	≥91.5	≥1300	For drawing non-ferrous metal wire and stainless steel wire etc.
YG6	K10	14.75-15.1	≥89.5	≥1520	For drawing steel ,nonferrous alloy bars of less than dia 20mm under more stress and also for drawing tubes of less than dia 10mm.
					For drawing steel and nonferrous wire or bars of less than dia 6mm under not so much stress.
YG6X	K10	14.8-15.1	≥91.0	≥1420
YG8	K20-K30	14.6-14.9	≥89.	≥1470	For drawing steel and nonferrous bars and tubes,Also for manufacturing mechanical parts, tools and wear parts.
					For fabricating drawing dies of steel tubes and rods under high compreesibility ratio; punching, stamping, forging tools under large stress.
YG11		14.4	≥88.5	≥2420
YG15		13.9-14.2	≥86.5	≥2060	For drawing steel bars and tubes with a high reduction rate and for manufacturing anvils ,drilling and punching and impacting dies.
YG20		13.4-13.8	≥83.5	≥2480	For making punching and impacting dies for watch parts and musical instrunments springs, batteries shells and tooth paste shells, etc,Also for making punching and impacting dies for steel balls of small diameters, screws and nuts, etc.
YG20C		13.4-13.8	≥82	≥2480	For making cold heading and cold punching and impacting dies for standardized parts, bearing s, bullet head and shell.etc.
YG20D		13.4-13.8	≥82	≥2300	For making cold heading and cold punching and impacting dies for standardized parts, bearing s, bullet head and shell.etc.
YSN30		13.9-14.9	≥87	≥1900	It is a demagnetized cemented carbide suitable for manufacturing forming tools in industries of magnetism.

Producing process:

Categories of our products:

1) Carbide drawing dies;

2) Carbide rods;

3) Carbide strips;

4) Carbide inserts;

5) Carbide disc cutters;

6) Carbide balls/ tire studs/

7) Carbide drilling bits;

8) Carbide Plates,

9) Carbide cold-forging dies;

10) Other customized items.

About our service

1) OEM & ODM are welcomed;

2) customized design is available

3) reply your enquiry in 24 working hours.

4) experienced staffs answer all your questions in fluent English.