This is a great set of easy-reassembling LCD controller kit which is used to turn a bare laptop LCD panel into a desktop/PC monitor. It will be a surprise that your bare LCD will be of good use, and no longer be a waste. It supports most of the LCD panel from 12.1" to 19" with a DS interface and a resolution lower than 1440*900, plug&play kit, no need soldering.
Please remember to leave us your LCD Model Number when placing the order, it is very import for us to prepare the right kit for you.
Necessary Accessories for turning a LCD to desktop monitor: LCD Controller board, Inverter, DS cable, Keypad, VGA cable, Power Adapter. If you have already had a VGA cable and a power adapter (12V,4A), this kit is a great choice for you, else there are some other kind of kits for options in our store .
Have a try and you will get great surprise！
Then, are you going to get this kit？
Important Steps to Process your order with this kit:
Step 1: Please provide your LCD panel model no. by sending us the ebay message before bidding this item, so that we can advise a right kit for your LCD. (Usually, the model no. can be found on a sticker on the back of the LCD panel. If needed, disassemble the plastic shell and you will find the sticker）. If possible, please give us as more specification of your LCD as you can. Then wait for our reply.
Step 2: We will give you the reply as soon as possible after carefully selecting and testing the kit by our technical support, and then you can place the order, and pay for it. We will send the package via HongKong Post as soon as possible after cleared payment. (If you prefer express shipping, please contact us to pay additional shipping cost before payment.)
Step 3: Waiting for the package.
We will write corresponding program into the lcd controller board to match your LCD, so this kit will match against one very specific LCD Panel or others that have exactly the same specification. However, a programmer could help on different LCDs, that is, change the firmware of the LCD controller board by yourself. Be aware that different DS cables and Inverters will be needed to match different LCDs.
1. Please make sure that your LCD is ok before bidding this item, else you will be responsible for the incompatibility.
2. If you concern much about resolution setting, please reconsider before bidding!
3. We will try our best to prepare the right kit for you, such as writing the corresponding program into the controller board, selecting the suitable DS cable and the suitable inverter. But as we don't have an LCD exactly as yours at hand, we can just test the controller with our own LCD. For yours, you need to test it yourself to check if it works well or not. As you know, there are so many LCDs with many varieties in the market, sometimes we can't promise the exact compatibility. Please consider it before bidding! However, we have gained many success in preparing the kit for our customers in real store. So why not have a try to get surprise!
4. If you are not specialized in electronics or have doubts in operation, please contact us for instruction, as we are not able to responsible for wrong operation.
5. After finishing the connecting, please don't rush to power on! First, use multi-meter to test whether the GND of the LCD is connected with the GND of the controller board. If not, please check the connection again. If yes, please test whether there is a short circuit between the red wires and black wires of the DS cable. If there is a short circuit, it means opposite connection or other errors. Any problem, please feel free to contact us. DIY needs a certain professional knowledge, please kindly take the responsibility of the risk. No metal contact is allowed when powering on the controller board, otherwise short circuit may occur, which may cause unavailability of the controller board.
Successful Example (radicalboy_fr -- a French friend's Project ):
Instruction to connect the controller board to the LCD:
1. Take away the old inverter and old DS cable from the LCD panel.
2. Connect the new inverter and DS cable to your LCD panel.
3. Connect controller board with PC by VGA cable.
4. Input power of 12V,4A.
We have collected a few of the model no. in the following table which we have gained success for reference. However, no matter your model no. is listed in the table or not, welcome to contact us for more details, we probably will be able to find the solution for you as we are located in a huge electronic market in shenzhen, China.
||LP121X04 LP133X09 LP133X3 LP133X7 LP133X8 LP140WX1 LP141WH1 LP141WP1 LP141WX1 LP141WX3 LP141X10 LP141X12 LP141X13 LP141X3 LP141X7 LP141X8 LP141XA LP141XB LP150E05 LP150X04 LP150X08 LP150X09 LP150X1 LP150X2
||LT133X1 LT133X7 LT133X8 LT141X4 LT141X5 LT141X6 LT141X7 LT150X3 LTA150XH LTM150X0 LTN141AT03 LTN141P4 LTN141W1 LTN141WD LTN141X7 LTN141X8 LTN141XA LTN141XB LTN141XC LTN141XF LTN150P2 LTN150PE LTN150XB LTN150XD LTN150XG LTN152W3 LTN154X1 LTN154X3
||B121EW01 B121EW02 B133BEW01 B133XN02 B141EW01 B141EW02 B141EW03 B141EW04 B141XG03 B141XG05 B141XG09 B141XN03 B141XN04 B150XG01 B150XG02 B152EW01 B154EW01 B154EW02 B154PW02 B154SW01 G150XG03 M150XN07 UB133X01 UB141X01 UB141X02 UB141X03
||00K3120(00K3190) 00K3220/ITXG72H 07K5500 07K5540 07K8466/ITXG77C 25L8400/ITXG75 26L4500/ITXG64 IAQX10N ITUX97E 55P4540/IAXG02D IASX12S IAXG01M IAXG02L5 ITXG06 ITXG77H
||LTD121EA4XY LTD121EA6N LTD121EA8K LTD121EX1S LTD121KAOS LTD133EX2X LTD141EA0V LTD141EC7F LTD141KN5K LTD154EX0T LTM12C270 LTM12C278F LTM12C283 LTM12C318 LTM12C328L LTM13C407 LTM13C420 LTM14C433 LTM14C500G LTM14C502K LTM14C502U
||TX31D72VC1CAA TX34D62VC1CAC TX34D71VC1CAA TX34D74VC1CAA TX34D76VC1CAA TX36D70VC1CAF TX36D71VC1CAA TX36D77VC1CAA TX36D81VC1CAA TX36D97VC1CAA TX38D14VC0CAA TX38D81VC1FAE TX38D83VC1FAB TX38D94VC1FAF
||N121i3 N141A1 N141C1 N141I1 N141I3 N141X201 N141X202 N141X5 N141X6 N141X7 N150X3 N154C3
||LQ106K1LA01 LQ121S1LH02 LQ133K1LA04 LQ133X1 LQ13X02C LQ141X1 LQ150U1 LQ150X1
||QD141X1 QD14FL02 QD14FL07 QD14TL01 QD14XL07 QD15AL02 QD15TL02 QD15TL07 B1548W01
||TM121SV-02L03B TM121XG-02L02A TM133XG-02L07A TM133XG-A02-01 TM150XG-02L02E TM150XG-26L10
||NL10276BC28 NL8060BC31 HSD141PX11HSD150MX17 HSD150PX16 TD141TGCB1 TD141TGCD1 TD141THCA1 HT13X14 HT14X12 HT14X13 HT12X13 HT14X19 HT150X02 HV150VX1 CLAA121WA01A CLAA140WA01 CLAA141XD05 CLAA154WA05A ......
- 1 X LCD Controller Board
- 1 X Inverter
- 1 X 5 keys Keypad
- 1 X DS cable
- a few other necessary cables for this kit
As we need to select the right inverter and ds cable to match your lcd for you, so they may be not the same as that shown in the picture. Hope for your understanding.
Welcome to customize your own kit!