Weather proofing silicone sealant

Weather proofing silicone sealant
Model:WP236
Brand:mimdy
Origin:Made In China
Category:Chemicals / Adhesives & Sealants
Label:silicone sealant , weather proofing
Price: US $0.8 / pc
Min. Order:1000 pc

Product Description

~Features:
1.One component,neutralcuring,with excellent adhesion ,weatherability and elasticity for weather sealing in curtain wall and building facades, especially suits applications in the areas with large difference in temperature and low humidity.
2.Good compatibility with other neutral silicone sealants.
3.Excellent weatherability and high resistance to ultraviolet radiation, heat and humidity, ozone and temperature extremes; virtually unaffected by sunlight, rain, snow and ozone.
4.Remains flexible over a temperature range of -58°F(-50℃) to 302°F(150℃).
5.Extension/compression movement capability of up to ±25percent of the original joint width.
6.The material is supplied as a paste, which cures into extremely tough elastomeric silicone rubber ensuring a durable, flexible, watertight bond upon exposure to atmospheric moisture.

Main applications :  
1.Weather sealing in glass curtain wall joints and building facades.
2.Sealing in expansion joints for concrete, plastic and metal etc..
3.Weather sealing in metal, enamel curtain wall joints.
4.Sealing in roof joints and ACP curtain wall joint.
5.Many other applications for movement joint.

Limitations:
1.Can not be used in structural glazing applications or where the sealant is intended as an adhesive.
2.Is not appropriate for all will be leaking oil, plasticizer or solvent surface.
3.Is not suitable for airtight place, because the silicone sealant need absorb air gas in the water cure.
4.Not for frost or wet surface.
5.Can not apply to the place where movement capability greater than ±25% of the original joint width.
6.Is not suitable for the place of continuous immersion or year-round moisture.
7.Surface temperature is not below 0℃ or above 50 ℃.
8.Can not ontact with strong acids or bases.
9.Hasn’t performed adhesion and compatibility tests on project substrates and all accompanying accessories.
10.Not to copper, zinc or lead coated surfaces.

Typical properties:
These values are not intended for use in preparing specifications.

Test Method Property Unit Standard Result
GB/T 13477 (ISO 7390) Slump mm ≤3≤3 00
GB/T 13477 (ISO 8394) Extrusion rate ml/min ≥80 800172
GB/T 13477(ASTM D 2377) Tack free time h ≤3 1.5
GB/T 13477 (ISO 7389) Extension recovery % ≥80 94
GB 16776 (ISO 10563) Weight loss % ≤10 6.6
GB/T 13477 (ISO 8339) Modulus at 23℃ MPa >0.4 0.68
GB/T 13477 (ISO 11600) Movement capability % ±25 ±25
GB/T 13477 Extension/compression rate % ±25 ±25
GB/T 13477 Adhesion at fixed stretch  No failure No failure
GB/T 13477 Adhesion after heat contract and cold extension  No failure No failure
GB/T 13477 Adhesion after UV-water exposure  No failure No failure
*GB: Chinese National Standard

ASTM: American Society for Testing and Materials

ISO: International Standardization Organization
The “GB” testing method is equivalent or partly equivalent to that in the“( )”

Installation:
1.Surface preparation: Sealants may not adhere or maintain long-term adhesion to substrates if the surface is not prepared and cleaned properly before sealant application.Using proper materials and  and cleaning procedures is vital for sealant adhesion.
2.Cleaning materials:clean, fresh solvent; clean, white cloths free of lint or other lint-free wiping materials; primer (when required).
3.Cleaning procedures:Remove all loose material (such as dirt and dust), plus any oil, frost or other contaminants from the substrates to which the sealant will be adhered. Do not use detergent to clean the substrate as residue may be left on the surface. Wet one rag with solvent and wipe the surface with it, then use the second rag to wipe the wet solvent from the surface before it evaporates. Change the cleaning rags frequently, as they become soiled. If cleaned areas are again exposed to rain or contaminants, the surface must be cleaned again.
4.Primers: WP236weather proofing silicone sealant will bond to many clean surfaces without the aid of a primer. For difficult-to-bond substrates, the use of a primer or special surface preparation should be evaluated.

Emergent Treatment:
Keep out of reach of children. Once it contacts skin or eye by accident, rinse the affected part with water for 15 minutes or turn to doctor for help immediately.

Shelf Life:
12 months from the manufacture date stored in cool & dry place below 27 ℃.

Color:

Clear, black, white, gray, other colours as clients’requirement.

Packing/ Mix Ratio:

Packing  A component:185L,B component:18.5L;A component:18.5L,B component:300ml*7. Mix Ratio by Volume  A:B = 10:1.

 

LIMITED WARRANTY INFORMATION – PLEASE READ CAREFULLY

The information contained herein is offered in good faith and is believed to be accurate. However, because conditions and methods of use of our products are beyond our control, this information should not be used in substitution for customer’s tests toensure that Foshan Shunde Mimdy Sealant Co., Ltd.’s products are safe, effective, and fully satisfactory for the intended end use.

FOSHANSHUNDE MIMDY SEALANT CO., LTD.SPECIFICALLY DISCLAIMS ANY OTHER EXPRESS OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY.

FOSHAN SHUNDE MIMDY SEALANT CO., LTD. DISCLAIMS LIABILITY FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES.

Weather proofing silicone sealant 1

Member Information

Foshan Shunde Mimdy Sealant Co., Ltd.
Country/Region:Guang Dong - China
Business Nature:Manufacturer
Phone:15916085149
Contact:Giison (Sales Representative)
Last Online:21 Jun, 2015