Technical Parameters Of The Equipment

PCB width

50mm-350mm

PCB transport height

750mm±50mm

PCB transport speed

0-2000mm／min

PCB transport angle（welding angle）

3º-7º

PCB Transport direction

L→R or R→L

PCB component height restrictions

100mm

The length of the preheating zone

1800mm

preheating zone number

3

The power of the preheating zone

9kw

The length of the preheating zone

Can be adjusted by the room temperature to 250 degrees

Heating Type

Infrared heating

Number of cooling zone

3

cooling method

Compulsory air-cooled

Apply solder type

Lead-free solder or Ordinary solder

The power of tin stove

11kw

Furnace capacity

320KG

Tin stove temperature

From room temperature to 300 degrees.，Control accuracy  ± 1 ℃

Temperature control mode

PID+SSR

The whole machine control mode

PC and Mitsubishi plc

Flux capacity

5.2L

Flux Flow

10ml-100ml/min

Spray method

Japanese SMC rodless cylinder and Taiwan QiBao nozzle

power supply

3-phase 5-wire 380V

Starting power

21kw

rated power

3.5kw

Air pressure

4~7KG/CM2  

The size of the rack

L3350×W1200×H1650MM

Installation dimensions

L4100×W1300×H1650MM

Weight

800kg

Preheating System

Preheat zone extended

1800mm/3 independent temperature control, long preheating zone, can provide a wide range of adequate warm-up room for adjustment, can eliminate undesirable large components on PCB soldering phenomenon, Three elongated preheating, reduce PCB board several attacks, PCB board heated evenly, can improve production efficiency.

Temperature control

Mitsubishi temperature acquisition module, PID temperature control is accurate, reliable, imported thermocouple test system, do a thermocouple exception alarm function

Heating section

Ceramic heater, fast heat, long life, low thermal inertia; the bottom of the direct heat radiation of the PCB, uniform temperature zones, each zone temperature complementary, no groove phenomenon.

Preheat power

9kw

Transportation Systems

Rail Material

SIMT special high temperature resistant aluminum rail. Stainless steel rails using a special thermal compensation, anti-deformation telescopic structure to ensure that no deformation can not afford to board rail

Rail Precision

Two synchronized rail width adjustment means, worm, worm precision screw-width-modulated, accuracy within 0.2mm width adjustment, the two support rails make consistent parallel and consistent length, the entire rail mounting.

Width-modulated mode

Width adjustment manually

Transport speed

100 -2000mm／min

C / V speed deviation range

Electronic closed-loop control precision within 0 to 10 mm / min

Motor Transport

Taiwan STK 60W inverter motor, belt force limiters overload protection device

Tin stove System

Tin stove material

3MM thick titanium alloy material, high temperature resistance, corrosion resistance, adapt to lead-free technology, long life;

Tin stove advantage

Special structure wettability spout，the way to progress into the furnace (traditional for the next way into the tin), reduce solder oxidation, easy to maintain, does not produce a floating black powder tin slag; tin furnace capacity 280kg

Low oxidation design

High strength tin stoves, high thermal stability, the use of liquid tin-flow design principles, reduce the impact of tin oxide because caused by continuous work 8 hours oxide slag is minimal. Lead solder 2.0kg / 8H, lead-free solder 1.8kg / 8H. Tin tin slag containing impurities different about bias. Applicable Sn / Ag / Cu, Sn / Zn, Sn / Cu lead-free solder

Tin stove moving way

Manually

Tin wave height adjustable

0-12MM

Heating system

The United States cast Watt heating plate, long service life. External heating system, using upper and lower heating furnace heating, more accurately, not burst tin! Maintenance very convenient.