Drip Irrigation Suspension Roller Concrete Pipe Making Machine

 

Two types of Concrete Pipe Machine: 

                

                  Centrifugal well pipe making machine                                  Roller suspension concrete pipe machine

 

 

 

Introduction of Centrifugal Concrete  Pipe machine:

    The machine takes sands, stones and cement as raw materials to produce many kinds of reinforced concrete drainage pipe with the length of 1000-4000mm, internal diameter of 200-4000mm with the mouth shapes of flat, tongue and groove and socket and spigot. All mechanical indexes have meet the national standards. They have been used widely in deep well, municipal drainage, expressway and other water supply and sewerage works with higher level required. The production efficiency can reach 4-5 piece/hour.

 

 

Technical of Centrifugal Type Pipe Making Machine:

 

    The centrifugal machine is mainly used to manufacture the centrifugal equipments manufacturing the reinforced concrete drainpipes, driving the spinning of the drainpipe concrete pipe mold loaded with some concrete and reinforcing steel with a certain mixing ratio at different speeds, and  the solid phase particles of concrete in steel mould will be centrifugal settling in the steel mould inner surface under centrifuge, meanwhile draining the excessive water, thus forming compacting concrete structure namely reinforcing concrete drainpipe. The machine mainly consists of riding wheels, shafts, bearing block, bearing, V-blet pulley, base and electromagnetic speed-controlling motor.

 

No.	Item		Unit	Model
				Double-wheel	Three-wheel
1	Riding wheel thread		MM	1870
2	Riding wheel wheelbase		MM	1500-2800
3	Riding wheel external diameter		MM	800-920
4	Riding wheel width		MM	100
5	Angle between wheel center and the center of steel mould		(°)	75°-110
6	The Max. length of molding drainage pipe		M	2-4
7	The Max. diameter of molding drainage pipe	Plain top/tongue and groove/pipe-jacking	MM	Φ2600	Φ1800
		Bell and spigot		Φ1800	Φ1800
8	The motor power		KM	37-90	55-132
9	The range of speed of main drive axle		r/min	100-500(continuous)	100-500(continuous)

 

 

 

 

Introduction of Roller Suspension Concrete Pipe Machine:

 

      Suspension roller type drain pipe making machine is a kind of perfect machine and equipment to produce reinforced concrete pipes and Pre-stressed concrete pipe. This machine is capable to make pipes with diameter from 300-2000mm and with length from 2-4meters. We can design many kinds of the pipe joint, including flush joint, socket & spigot joint And all the concrete pipes are widely used inadministrative drainage, agricultural field irrigation, road culvert and deep water well.

 

Technical of Centrifugal Type Pipe Making Machine:

 

    This machine uses the Roller to support the concrete pipe mould, and produce the roller force to concrete in the mould. When the roller rotate at a high speed, the concrete in the mould will spread in the inner wall of the pipe mould and form a cement pipe with the centrifugal force, and when the mould with the inner concrete pass on the roller, the concrete between the mould and the roller will be compacted solid to form a pipe.

 

	XG 200-600	XG 800-1200	XG 1000-1500	XG 4M
Diameter	200-600mm	800-1200mm	1000-1500mm	300-2000mm
Length	2000mm	2000mm	2000mm	1000-4000mm
Power of Motor	15KW	45KW	90KW	110KW
Capacity	10-15Pc/h	8-12Pc/h	6-10Pc/h	6-8Pc/h
Labor demand without feeding machine	4-5	4-5	4-5	4-5
Labor demand with feeding machine	3-4	3-4	3-4	3-4
Joint	Plain,socket and spigot,male and female	Plain,socket and spigot,male and female	Plain,socket and spigot, tongue and groove	Plain,socket and spigot,tongue and groove

 

Joint Type of The Pipe Mould:

    Concrete pipe mold fall into two types according to the way of connection of the shaped drain pipes: rigid joint and flexible joint; pipe mold fall into three types according to the joint shape of shaped drain pipes: tongue and groove, bell and spigot, plain pipe mold fall into Ⅰ,Ⅱ,Ⅲ grades according the grade difference of external pressure load of shaped drain pipes.

 

 

Features of Concrete Pipe Mould:

 

1.The adoption of integrated design is reinforced design of leakproof slurry, no rough edges on which the mouth of pipe joints, easy mold-opening.

 

2 .The friction rings in the molds are all made of 45 cast steel.

 

3 .The steel plate we use is produced by Laigang which is one of the four major steel mills, and its abrasion resistance will be guaranteed.

 

4 .The carbon-dioxide arc welding is applied into the all welding. The plasma cutting machine is used for cutting. Welding seam is smooth and nice, and the cutting seam is very exquisite. All above ensure the mold tough and durable and extend the service life greatly.

 

Related Equipment:

 

1. Concrete Mixers (rotary-drum-type, double-horizontal-shaft);

2. Concrete Batchers;

3. Concrete Mixing/Batching Plants (25-480m3/h, stationary, mobile, conventional-type, compact-type, simple-type, commercial-type);

4. Electiric pole making mould (8M-18M, round/square)

5.Well pipes and drain pipes making mould(2m,4m,8m)

6. Suspension cement pipe making machine

7. Centrifugal machine

8. Vertical extrusion molding machine

9. Reinforcement cage  seam welder

10.Boiler

11.Feeding machine

 

Certificate: 

 

Packaging:

 

    Different Machines with Different Package, The products should be processed to be rustproof and moisture proof before delivery. The barrels are nude packed, Motors, Electric Switch Box and spare parts are packed in wooden cases.

 

Our Services:

1. Provide complete production line supporting machines with high performance and good quality;

2. Provide reasonable design of plant,office, warehouse etc and related drawings according to customers' requirements.

3. Provide all machines layout plan in production plant and responsible for the layout of machines.

4. Responsible for all Installation and commissioning of all machines as well as the workers production training.

5. Promise to supply required wearing parts of machines as per requirements of customers timely with favorable prices within 2 years.

 

Contact:

 

If you trust me You come to China I can be your guide !

 

Welcome to visit our factory!

Drip Irrigation Suspension Roller Concrete Pipe Making Machine

 

Two types of Concrete Pipe Machine: 

                

                  Centrifugal well pipe making machine                                  Roller suspension concrete pipe machine

 

 

 

Introduction of Centrifugal Concrete  Pipe machine:

    The machine takes sands, stones and cement as raw materials to produce many kinds of reinforced concrete drainage pipe with the length of 1000-4000mm, internal diameter of 200-4000mm with the mouth shapes of flat, tongue and groove and socket and spigot. All mechanical indexes have meet the national standards. They have been used widely in deep well, municipal drainage, expressway and other water supply and sewerage works with higher level required. The production efficiency can reach 4-5 piece/hour.

 

 

Technical of Centrifugal Type Pipe Making Machine:

 

    The centrifugal machine is mainly used to manufacture the centrifugal equipments manufacturing the reinforced concrete drainpipes, driving the spinning of the drainpipe concrete pipe mold loaded with some concrete and reinforcing steel with a certain mixing ratio at different speeds, and  the solid phase particles of concrete in steel mould will be centrifugal settling in the steel mould inner surface under centrifuge, meanwhile draining the excessive water, thus forming compacting concrete structure namely reinforcing concrete drainpipe. The machine mainly consists of riding wheels, shafts, bearing block, bearing, V-blet pulley, base and electromagnetic speed-controlling motor.

 

No.	Item		Unit	Model
				Double-wheel	Three-wheel
1	Riding wheel thread		MM	1870
2	Riding wheel wheelbase		MM	1500-2800
3	Riding wheel external diameter		MM	800-920
4	Riding wheel width		MM	100
5	Angle between wheel center and the center of steel mould		(°)	75°-110
6	The Max. length of molding drainage pipe		M	2-4
7	The Max. diameter of molding drainage pipe	Plain top/tongue and groove/pipe-jacking	MM	Φ2600	Φ1800
		Bell and spigot		Φ1800	Φ1800
8	The motor power		KM	37-90	55-132
9	The range of speed of main drive axle		r/min	100-500(continuous)	100-500(continuous)

 

 

 

 

Introduction of Roller Suspension Concrete Pipe Machine:

 

      Suspension roller type drain pipe making machine is a kind of perfect machine and equipment to produce reinforced concrete pipes and Pre-stressed concrete pipe. This machine is capable to make pipes with diameter from 300-2000mm and with length from 2-4meters. We can design many kinds of the pipe joint, including flush joint, socket & spigot joint And all the concrete pipes are widely used inadministrative drainage, agricultural field irrigation, road culvert and deep water well.

 

Technical of Centrifugal Type Pipe Making Machine:

 

    This machine uses the Roller to support the concrete pipe mould, and produce the roller force to concrete in the mould. When the roller rotate at a high speed, the concrete in the mould will spread in the inner wall of the pipe mould and form a cement pipe with the centrifugal force, and when the mould with the inner concrete pass on the roller, the concrete between the mould and the roller will be compacted solid to form a pipe.

 

	XG 200-600	XG 800-1200	XG 1000-1500	XG 4M
Diameter	200-600mm	800-1200mm	1000-1500mm	300-2000mm
Length	2000mm	2000mm	2000mm	1000-4000mm
Power of Motor	15KW	45KW	90KW	110KW
Capacity	10-15Pc/h	8-12Pc/h	6-10Pc/h	6-8Pc/h
Labor demand without feeding machine	4-5	4-5	4-5	4-5
Labor demand with feeding machine	3-4	3-4	3-4	3-4
Joint	Plain,socket and spigot,male and female	Plain,socket and spigot,male and female	Plain,socket and spigot, tongue and groove	Plain,socket and spigot,tongue and groove

 

Joint Type of The Pipe Mould:

    Concrete pipe mold fall into two types according to the way of connection of the shaped drain pipes: rigid joint and flexible joint; pipe mold fall into three types according to the joint shape of shaped drain pipes: tongue and groove, bell and spigot, plain pipe mold fall into Ⅰ,Ⅱ,Ⅲ grades according the grade difference of external pressure load of shaped drain pipes.

 

 

Features of Concrete Pipe Mould:

 

1.The adoption of integrated design is reinforced design of leakproof slurry, no rough edges on which the mouth of pipe joints, easy mold-opening.

 

2 .The friction rings in the molds are all made of 45 cast steel.

 

3 .The steel plate we use is produced by Laigang which is one of the four major steel mills, and its abrasion resistance will be guaranteed.

 

4 .The carbon-dioxide arc welding is applied into the all welding. The plasma cutting machine is used for cutting. Welding seam is smooth and nice, and the cutting seam is very exquisite. All above ensure the mold tough and durable and extend the service life greatly.

 

Related Equipment:

 

1. Concrete Mixers (rotary-drum-type, double-horizontal-shaft);

2. Concrete Batchers;

3. Concrete Mixing/Batching Plants (25-480m3/h, stationary, mobile, conventional-type, compact-type, simple-type, commercial-type);

4. Electiric pole making mould (8M-18M, round/square)

5.Well pipes and drain pipes making mould(2m,4m,8m)

6. Suspension cement pipe making machine

7. Centrifugal machine

8. Vertical extrusion molding machine

9. Reinforcement cage  seam welder

10.Boiler

11.Feeding machine

 

Certificate: 

 

Packaging:

 

    Different Machines with Different Package, The products should be processed to be rustproof and moisture proof before delivery. The barrels are nude packed, Motors, Electric Switch Box and spare parts are packed in wooden cases.

 

Our Services:

1. Provide complete production line supporting machines with high performance and good quality;

2. Provide reasonable design of plant,office, warehouse etc and related drawings according to customers' requirements.

3. Provide all machines layout plan in production plant and responsible for the layout of machines.

4. Responsible for all Installation and commissioning of all machines as well as the workers production training.

5. Promise to supply required wearing parts of machines as per requirements of customers timely with favorable prices within 2 years.

 

 

 

We promise our customers:

 

 

High Qaulity ,

Professional Guidance,

Satisfactory After-Sale Service!

 

 

 

Warmly Welcome To Visit Our Factory  !