Model: | SYH-08M-012F |
---|---|
Brand: | Syhdee |
Origin: | Made In China |
Category: | Consumer Electronics & Lighting / Lighting / LED Lighting |
Label: | led tube light , led lamp light tube , led tube t8 |
Price: |
US $3.8
/ pc
|
Min. Order: | 500 pc |
General Introduction
DLC 140LM/W High Lighting Effect Led Light 9W 18W 20W led tube light 1200mm 1500mm led tubo
LED tube lights t8 adopts 5000K SMD LED2835 as light source and there are 2ft(600mm), 4ft(1200mm) in dimension and 8W, 15W, 18W, 22W in power available.
LED tube lights t8 18W works with the standard AC100-277V voltage input and DC50-60V voltage output. 18W 4ft LED tube lights t8 is widely applied in factory, hotel, school, supermarket, etc. It is DLC qualified.
A |
C |
Caps |
||
Minimum |
Maximum |
Minimum |
Maximum |
Size |
1197mm |
1198mm |
1213mm |
1214mm |
12.7mm
|
LED Tube Lights T8 Parameters
Model NO. |
SYH-08M-012F(5000K) |
|
Optical Parameters |
Light Source |
SMD LED2835 |
Luminous Flux(lm) |
1800 |
|
CCT(K) |
5000 |
|
CRI(Ra) |
80 |
|
Beam Angle |
120°-160° |
|
Light Attenuation ratio (%) |
Less than 10% in 3 years |
|
LED Quantity |
144 | |
Electrical Parameters |
Input Voltage(V) |
AC100-277V |
Frequency(Hz) |
50/60HZ |
|
Output Voltage(V) |
DC50-60V |
|
Total Power(W) |
18 |
|
Power Factor |
>0.9 |
|
Lifespan (Hrs) |
>50,000 |
|
Dielectric Voltage Withstand Test |
1500Vac/60s |
|
Structure Parameters |
Material |
Aluminum housing &PC cover |
Size(mm) |
Φ26×1200 |
|
Length(mm) |
1200 |
|
Net Weight(g) |
320 |
|
Integrated Parameters |
Operating Temperature |
-20°-40° |
Storage Humidity |
-40°-85° |
|
Safety Requirement |
DLC qualified |
|
Environmental Directives |
RoHS |
LED Tube Lights T8 Application
LED tube lights t8 can be applied in indoor LED lighting, places as office, supermarket, school, factory, hotels, malls, buses, warehouse, etc.
LED Tube Lights T8 Installation
LED Tube Lights T8 Wiring Diagram:
1) Turn off electric power before LED Tube Lights installation
2) For refitting old fluorescent lamp with a single-side-power-input LED tube lights t8, please re-connect your wire as the following diagram.
3) For diagram A1 loop with magnetic ballast & starter, please remove the starter first. Then connect line N and Line L to the same side socket but separately.
Now you can put on the LED tube and turn it on. And the loop has been changed into the one as showed in diagram A2.
Note: You can just keep magnetic ballast as it was. However, it’ll consumer some power. For saving energy, it’s still s ested to remove it if your labor cost is not so high.
4) For diagram B1 loop with electronic ballast, please remove the electronic ballast first. Then connect line N and Line L to the same side socket but separately.
Now your LED tube light is ready to work. And the loop has been changed into what showed in diagram B2.
Shenzhen Syhdee Co., Ltd. | |
---|---|
Country/Region: | Guang Dong - China |
Business Nature: | Manufacturer |
Phone: | 13316918221 |
Contact: | Maggie (Marketing) |
Last Online: | 15 Dec, 2015 |