Model: | - |
---|---|
Brand: | hongyuan |
Origin: | Made In China |
Category: | Electronics & Electricity / Other Electrical & Electronic |
Label: | SBS , waterproof membrane |
Price: |
US $3
/ pc
|
Min. Order: | 1000 pc |
SBS modified bitumen membrane is made by saturating the base in bitumen, or thermoplastic elastomer (such as styrene butadiene-SBS), reinforced with polyester or fiberglass, finishing the upward face with fine sands, mineral slates(or grains) or polythene membrane etc.
APP modified bitumen membrane is made by saturating the base in bitumen, or thermoplastics (such as APP,APAO,APO), then covering double faces with thermoplastic elastomer (SBS) and last finishing the upward face with fine sands, mineral slates(or grains) or polythene membrane etc. while downward face with fine sands or polythene membrane.
Characteristic
Good impermeability. Possess good tensile strength, elongation rate and size stability which could be well suited the substrate distortion and crack.SBS modified bitumen membrane is specially being applied in the cold area with low temperature, while APP modified bitumen membrane is applied in the hot area with high temperature. Good performance in anti-puncture, anti-broker, anti-resistance, anti-erosion, anti-mildew, anti-weathering. Construction is convenient, the melt method can operate in four seasons, joints are reliable
Specification
Item |
Type |
PY Polyester G Glassfibre PYG Glassfibre enhance polyester felt PE PE Film S Sand M Mineral |
||||||
Grade |
I |
II |
||||||
Reinforcement |
PY |
G |
PYG |
|||||
Surface |
PE |
San |
Mineral |
|||||
Thickness |
2mm |
3mm |
4mm |
5mm |
||||
With |
1000mm |
Applicable scope
Suitable for civil building roofing, underground, bridge, parking, pool, tunnel in the line of waterproofing and damp proof, especially for the building under high temperature. According the roofing engineering stipulation, APP modified bitumen membrane could be used in the Grade civil building and industrial building which has special waterproofing requirement.
Storage and transportation instructions
Technical data
SBS [Confirming to GB 18242-2008]
No. |
Item |
I |
II |
|||||||||||
PY |
G |
PY |
G |
PYG |
||||||||||
1 |
Soluble content/(g/m ²)≥ |
3cm |
2100 |
* |
||||||||||
4cm |
2900 |
* |
||||||||||||
5cm |
3500 |
|||||||||||||
Test |
* |
No flame |
* |
No flame |
* |
|||||||||
2 |
Heat resistance |
℃ |
90 |
105 |
||||||||||
≤mm |
2 |
|||||||||||||
Test |
No flow, no dripping |
|||||||||||||
3 |
Low temperature flexibility/℃ |
-20 |
-25 |
|||||||||||
No crack |
||||||||||||||
4 |
Impermeability 30 minutes |
0.3MPa |
0.2MPa |
0.3MPa |
||||||||||
5 |
Tension |
Maximum/(N/50mm) ≥ |
500 |
350 |
800 |
500 |
900 |
|||||||
Secondly-Maximum |
* |
* |
* |
* |
800 |
|||||||||
Test |
No crack, no apart |
|||||||||||||
6 |
Elongation |
Maximum/%≥ |
30 |
* |
40 |
* |
* |
|||||||
Secondly-Maximum≥ |
* |
* |
15 |
|||||||||||
7 |
Oil Leaking |
Pieces≥ |
2 |
APP [Confirming to GB 18242-2008]
No. |
Item |
I |
II |
||||||||||||
PY |
G |
PY |
G |
PYG |
|||||||||||
1 |
Soluble content/(g/m²)≥ |
3cm |
2100 |
* |
|||||||||||
4cm |
2900 |
* |
|||||||||||||
5cm |
3500 |
||||||||||||||
Test |
* |
No flame |
* |
No flame |
* |
||||||||||
2 |
Heat resistance |
℃ |
110 |
130 |
|||||||||||
≤mm |
2 |
||||||||||||||
Test |
No flow, no dripping |
||||||||||||||
3 |
Low temperature flexibility/℃ |
-7 |
-15 |
||||||||||||
No crack |
|||||||||||||||
4 |
Impermeability 30 minutes |
0.3MPa |
0.2MPa |
0.3MPa |
|||||||||||
5 |
Tension |
Maximum/(N/50mm) ≥ |
500 |
350 |
800 |
500 |
900 |
||||||||
Secondly-Maximum |
* |
* |
* |
* |
800 |
||||||||||
Test |
No crack, no apart |
||||||||||||||
6 |
Elongation |
Maximum/%≥ |
30 |
* |
40 |
* |
* |
||||||||
Secondly-Maximum≥ |
* |
* |
15 |
Construction Points
Overlapping--overlapping between sheets shall be completely adhered, with 80-100mm width of jointed area.
Vertical surface ends--fasten with metal battens and bolts, coat special sealant in all edges.
Attentions for Construction
Construction shall not be carried out be carried out in rain,snow or over 5 degree wind weather.
There shall be sufficient safety protective facilities in construction site,place firefighting devices according to stipulations.
Installation Sketch point
1.Clean the substrate using broom or high pressure dusty cleaner.
2.Apply primer
3.Heat membrane bottom using a high temperature flame gun.
4.Push forward while the primer and membrane oil melted.
5.Use roller to push hard the membrane surface to ensure it stick firmly.
Main point of construction plans
Membrane waterproof of underground structure
Membrane waterproof structure of pond
Roofing waterproof membrane structure
Road and bridge construction waterproof membrane
weifang hongyuan waterproof materials co.,ltd | |
---|---|
Country/Region: | Shan Dong - China |
Business Nature: | Manufacturer |
Phone: | 15163601048 |
Contact: | ellen (sales) |
Last Online: | 24 May, 2016 |