Product introduction

Klida orthopedic splint is composed by manifold layers of orthopedic casting tapes and specially nonwoven fabrics. It is characterized by better viscosity, fast drying time, high rigidness after dying and light weight. Due to better bio compatibility, polyurethane is widely used in medical places. Animal study and acute and chronic toxicity test have proved that medical polyurethane was non-toxic and no-induced distortion, no local irritation and no allergic reaction.

 

Feature:

1 20 times stronger and 5 times lighter than the traditional plaster cast

2 Harden fast :functional strength will be achieved in 20 mins

3 Good air-permeability ,Water-proof,Good X-ray radiolucence

4 Easy operating and no harm to patients

 

How to use orthopedic casting splint ?

 

1) Select proper specification according to the surgery position

2) Put the pad (cotton coil or cotton slipcover) on the surgery position.

3) Immerse the roll in room temperature water(21-24°C) for 4-6 seconds and squeeze it 2-3 times firmly. If the water warmer than 21-24°C shortens the immersing time, while cooler than 21-24°C water lengthens the time.

4)Take the splint out and press out excrescent water;Absorb water drip of the splint surface with towel.

5) Put the splint on the fixed position, molding it according to need. Mold it in 3-5 minutes after immersing in water because after that time it will concretion. Allow about 10 minutes for sufficient concretion and let patients not move during this time. It could bear electric weight after 20 minutes.

6) Fix the splint with gauze bandage or elastic bandage after concretion

 

Storage:

Be careful not to break the package.

Store Klida Splint(Poly) at room temperature.

 

NOTE: Storage at higher lower temperatures may affect the shelf-life and handing properties of the product.

Damaged products by careless handing cannot be replaced. Please handle and store them carefully.

The shelf-life of Klida Splint(Poly) stored by the above method is about two years.

 

Warning:

1. The higher the water temperature is, the faster Klida Splint(Poly) hardens.

2. The setting time becomes shorter as the water absorption time increases.

3. Klida Splint can be used without immersing it in water if slow setting is needed. It may take approximately 15 minutes for the splint to harden without immersion in water.

4. The thick side of non-woven fabric should be applied to the desired area of the patient.

 

 

NO.	Specification			Carton Size  cm	Packing
KSF312	3”  7.5cm x 30cm/pc			65*49*44CM	1pc/bag, 20bags/box, 6boxes/ctn
KSF335	3”  7.5cm x 90cm/pc			65*49*44CM	1pc/bag, 10bags/box, 6boxes/ctn
KSF415	4”  10.0cm x 40cm/pc			65*49*44CM	1pc/bag, 15bags/box, 6boxes/ctn
KSF430	4”  10.0cm x 75cm/pc			65*49*44CM	1pc/bag, 10bags/box, 6boxes/ctn
KSF530	5”  12.5cm x 75cm/pc			84*50*46CM	1pc/bag, 10bags/box, 6boxes/ctn
KSF545			5”  12.5cm x 115cm/pc	84*50*46CM	1pc/bag, 5bags/box, 6boxes/ctn
KSF630		6”  15cm x 75cm/pc		84*50*46CM	1pc/bag, 10bags/box, 6boxes/ctn
KSF645		6”  15cm x 115cm/pc		84*50*46CM	1pc/bag, 5bags/box, 6boxes/ctn

 

 

Recommended amount of usage

Size	Usage
2 inch	Childrens hands, fingers, and toes
3 inch	Childrens wrists, ankles, and arms and legs
4 inch	Childrens legs and ankles, adults hands and wrists
5 & 6 inch	Adults arms and legs