Orthopedic casting tape is composed by manifold layers of special made fiberglass, which was soaked by polyurethane. Polyurethane material is one kind of block co-polymer which contains soft segment and it is characterize by better viscosity, fast drying time, high rigidness and light weight. Due to better bio-compatibility, polyurethane is widely used in medical fields. Animal study and acute and chronic toxicity test have proved that medical polyurethane is non-toxic and no induced distortion, no local irritation and no allergic reaction.

Character & advantage

1) Simple operation: Room temperature operation, short time, good molding feature

 2) High hardness & light weight

 20 times hard than plaster bandage; light material and use less than plaster bandage;

 Its weight is plasters 1/5 and its width is plasters 1/3,which could reduce wound burden

 3) lacunary (many holes structure) for excellent ventilation

 Unique knitted net structure make sure good air ventilation and prevent skin damp and hot & pruritus.

 4) Rapid ossification (concretion)

 It ossifies in 3-5 minutes after open the package and could bear weight after 20 minutes, but plaster bandage need 24 hours for full concretion

 5) Excellent X-ray penetration

 Good x-ray penetration ability makes X-ray photo clearly without remove the bandage, but plaster bandage need remove to make x-ray inspection.

6) Good waterproofing quality

 The moisture -absorbed percent is 85% less than plaster bandage, Even the patient touch the water situation, it still could keep dry in the injury position

 7) Convenient operation & mold easily.

8) Comfortable & safe to patient/doctor

 Material is friendly to operator and it wont become tension after concretion.

 9) Wide application

 10) Environment friendly

 Material are environmental friendly, which could not produce polluted gas after inflammation.

 How to use casting tape:

 1) Put the pad (cotton coil or cotton slipcover) on the surgery position.

 2) Wear surgical gloves.

 3) Select proper specification according to the surgery position.

 4) Immerse the roll in room temperature water(21-24°C) for 4-6 seconds and squeeze it 2-3 times firmly. If the water warmer than 21-24°C shortens the immersing time, while cooler than 21-24°C water lengthens the time.

5) Enwind spirally; Overlapping the previous layer by one-half or two-thirds of the roll width. To maintain proper tension is very important and take care to avoid excessive tightness. The strength can be determined by the number of layers used. Just 3-4 layers provide a string non-weigh-bearing cast and 5-6 layers are typically adequate for weight-bearing cast.

6) Additional after the initial enwinding should be overlapped on itself to achieve good molding. Enwind the roll in 3-5 minutes after immersing in water because after that time it will be concretion.

7) Smooth and rub the surface to achieve good contact between layers. Keeping smoothness helps mold the wrap.

Allow about 10 minutes for sufficient concretion and let patients not move during this time. It could bear electric weight after 20 minutes.

8) It could be windowed, trimmed or removed with traditional cast saw equipment.

 

Specification

 

Fiberglass casting tape

 

model	Size/roll	packing
KCF02	5.0cm*360cm	10bags*12boxes/ctn
KCF03	7.5cm*360cm	10bags*12boxes/ctn
KCF04	10.0cm*360cm	10bags*12boxes/ctn
KCF05	12.5cm*360cm	10bags*9boxes/ctn
KCF06	15.0cm*360cm	10bags*9boxes/ctn

 

Size	Usage
2 inch	Childrens hands, fingers, and toes
3 inch	Childrens wrists, ankles, and arms and legs
4 inch	Childrens legs and ankles, adults hands and wrists
5 & 6 inch	Adults arms and legs