WOYO PDR-007 Paintless Dent Repair Heat Induction

WOYO paintless dent repair tool is a vehicle specifically for small and medium-sized dent repair.

1.Simple to operate, easy to use, low cost of learning.

2. rapid repair, to the same depression area, 10 times faster than traditional repair method.

Fast delivery to the owner, improve workshop utilization rate, rapid recovery of investment.

3. The two operating modes adapted to different requirements

(1)Time mode: under 100% power, 0.5 seconds -4 seconds, 7 file time setting, assess the size of the depression area, match the appropriate operating time by time gear, avoid poor time control to cause secondary damage.

(2) Power mode: 20%-100%  5 power settings, assess the size of the depression area, match the power shift with the appropriate power from small to large, realize the fast repair.

4. The high precision control, 85% imported chip equipment components, quality guarantee, stable and secure.

5. Large screen digital display, accurate control, real-time monitor.

Model: PDR-007
Input: Voltage 220-240V    
Frequency:50Hz         
Fuse:10A
Output: Peak Voltage 250V    
Frequency:40-45KHz    
Peak Power ≈ 800W

Packing List:

PDR Main*1
Main Cable*1
Power Cable*1
Repair Pen*3
Restoration Switch*1
One-year warranty


Manual

Before using this device, you must read the instructions. If the instructions are not followed carefully, the operator could suffer injury, the device could be damaged, or the car being treated might be damaged.

Before-use warning (MUST READ)
1. Not suitable for operation by those with pacemakers or artificial limbs with metal parts.
2. Before using this device, you must wear a safety mask, safety gloves, and safety clothing to avoid being burned during use.
3. Operators must not have any metal objects on their person during operation, including but not limited to watches, cuff links, keys, belt buckles, coins, or zippers.
4. This device cannot be operated in areas with conductive particulate matter, areas used forapplying paint, areas housing or handling chemical fuels, areas of high temperature, and areas of high humidity.
5. Once the device is powered on, flammable objects must be kept away from the device.
6. Before you power on the device, make sure that you have a fire extinguisher on hand in case any misoperation causes a fire.
7. Do not use this device in the vicinity of safety airbags.
8. Once the device is powered, there must be personnel on site to watch over the device. When the device is not in use, unplug the device's power cable.
9. This device should be stored at temperatures between 0 and 50 celsius. When transporting the device, avoid vibrations or shocks.

Important warnings for use (MUST READ)
1. While the restoration head is restoring a damaged car body, the temperatures of both the restoration head and the body will rapidly increase. Do not touch either the restoration head or the car body before they have had time to cool down.
2. While the restoration head is in the process of restoration, the temperatures of both the restoration head and the damaged area will rapidly increase. Using the restoration head on one area for too long may increase temperatures to the point of damaging the car's paint job
(it is recommended that every 1-1.5 seconds, the operator wipes down the damaged area with a wet rag in order to keep the temperature manageable).

• During the restoration process, the temperatures of both the restoration head and the damaged area will rapidly increase and the body of the car will immediately become softer. During restoration,make sure the restoration head is not applying pressure to the car, otherwise the
  restoration process itself might further dent the car.
  4.The "Time/effect Dial" intensity can be set between 20% and 100%. This is the strength that the device runs at. Press the "Work" button to activate the device. Let go of it and the device will stop.
  5.Connect the "Extension Cable" to the device's Quick Connect head and the Restoration Head's Quick Connection head, and the device is ready to use.
  6. After work is complete, set the "Time/effect Dial" to "OFF", and after 5-10 minutes, set the "ON/OFF Switch" to "OFF" as well. Give the device time to cool down, and then remove the "220V Power Cable". Every time you use the device, repeat the steps above for a safe and effective experience.
  
  Dent repair method
  Car body dent diagram
  
  First, according to the size of the dent and the color of the paint, set the work time and intensity of the Paint Damage-Free Dent Restorer. Typical use would see the "Time/effect Dial" set to 0.5-1 second(s). Grip the restoration head and press the "Work" button, and begin moving
  around the dented area. First trace around "area 1", moving in to "area 4" as you add heat. Wait for cool down. Then, begin at "area 2" and move towards "area 4" as you add heat. Wait for cool down.Then, begin at "area 3" and move towards "area 4" as you add heat. Wait for cool down.
  Finally,continually add heat in "area 4", then wait for cool down. The repair process should be complete.(Some areas might require repeated applications of heat or repetitions of the above processes)
  During the repair process, the operator MUST take note not to work in one area for more than 1 second. It is recommended that an operator applies compressed air or a wet rag to work areas to prevent overheating. During the restoration process, great amounts of heat will be created,causing the metal of the car to soften. Do not apply downwards pressure while restoring, or the dent will just become larger. During the restoration process, the operator MUST be mindful of the surface temperature of the car. If the heat gets too high, it will ignite the paint on the car's surface, causing greater damage. We s est the operator first practices on the piston cap of an unused engine or an abandoned car, this way the operator will learn the functions of the device as well as the dangers associated with its use. Proper use of equipment is the responsibility of any service provider!
  
  Suitable range of use

This device is designed specifically to be used with dents on flexible steel car bodies.
The diagrams below illustrate the types of dents that can be removed. Dents like the kind caused by impact from hailstones, which leave smooth, rounded dents, can be removed. (More active materials may call for different devices, like pull hooks or suction cups. Consult with training personnel for specifics)

Unsuitable range of use
Sharp dents Body areas that have been damaged and reconstructed
Crumpled/creased areas or dents along creased metal

Aluminum bodies
Using the device
1.Connect the "220V Power Cable" to the device's "Power Input Socket", and plug the other end of the cable into a 220V power socket. Flip the "ON/OFF Switch" to ON, which will turn on a red light. The "Work Status Display" will also turn on. This is the normal status of the device.

2.Once it turns on, the "Work Status Display" will display the WOYO logo, and will then display a loading message for about 10 seconds. This screen will display the work status of the device. The device itself will release an intermittent "beeping" sound. This is the normal status of
the device.  (Note: If the device continually displays a loading message, power it down, wait 5 minutes, then  power it on again. If it still displays a loading message, contact one of our distributors! )

3.The "Time/effect Dial" lets you select a run time between 0.5 seconds and 4 seconds, and the device runs at capacity regardless of the length of time selected. Press the "Work" button once to set run time.


Keywords:
Paintless Dent Repair
WOYO PDR-007
Paintless Dent Removal
AUTO BODY REPAIR
Heat Induction
Dent Repair
Dent Removal
Extreme Dent Removal 
WOYO Innovation
Hail Repair Tool 
shrink over-stretching metal dent
automatic control system
Automotive beauty 
conservation Electronic
Dent Repair
Car panel Conservation 
Effective on Steel
Automotive Repair System
Electronic Soft Dent Reduction 
dent removal tool
Car Body Paint Less Dent Puller