Product Description

stainless steel strip

Sakysteel offer a very comprehensive stainless steel strip, we can tailor made to cater the needs of various industrial and commercial segments including the automotive, petrochemical , electronic and pharmaceutical and holds contracts spring manufacturers.

stainless steel strip
Grade	• Grade 304/304L (UNS S30400/S30403, EN 1.4301/1.4307)  • Grade 316L (UNS S31603, EN 1.4404)  • Grade 409L (UNS S40900, EN 1.4512)  • Grade 430 (UNS S43000, EN 1.4016)  • Grade 441 (UNS S44100, EN 1.4509)
Thickness	10 – 750mm Other special dimensions are acceptable upon the request
Finish	• No.1 Hot Rolled Stainless Steel Strip • 2D Cold Rolled Stainless Steel Strip • 2B Cold Rolled Stainless Steel Strip  • BA Cold Rolled Stainless Steel Strip  • Brushed (No.3/No.4/No.5/No.5), Scotch Brite and Hairline Finish Stainless Steel Strip
Slitting Thickness	0.3 – 3.0mm
Coating	No paper, PE or Laser PE coating Paper Interleaved was acceptable depending on the width
Coil ID	Non-standard diameters will accepted depending on thickness and width of the coil
Slit edge	Normal slit edge (burr height will depend on the thickness)

Chemical Component
Grade	STS304	STS316	STS430
Cr(%)	18-20	16-18	16-18
Ni(%)	8-10	10-14	≤0.6
C(%)	≤0.08	≤0.07	≤0.12
Elong	Above 40	30MIN	Above 22
Hardness	≤200HV	≤200HV	Below 200

A wide range of finishes can be applied to stainless steel (ss). Sakysteel stocks material with many different mill finishes.

No. 1 Finish/HRAP - (Hot Rolled Annealed & Pickled, also called a No. 1 Finish) – This dull finish is common for heavy gauge material. In general, stainless steel over .1875” thick will be delivered as HRAP. It is also possible to have HR (Hot Rolled) or HRA (Hot Rolled Annealed) stainless steel;

No. 3 Finish – This finish is obtained with a ground unidirectional 80 to 100–grit abrasive. It is sometimes an intermediate step for finer finishes.

No. 4 Finish – This finish is obtained with a ground 150-grit abrasive.

No. 43 Finish – Appliance finish

No. 2 Finish - There are two variations of the No. 2 finish. Unless specified, either a 2D or a 2B will be delivered when a No. 2 finish is requested.
a. 2D 
This dull finish is achieved by cold-rolling, heat-treating & pickling. It is the standard finish for 439, 409, 436 and 441.
b. 2B Mill Finish

This mill finish is produced the same way as 2D, but a final light rolling pass gives the surface a smooth, reflective gray sheen. It is the standard finish for 201, 301, 304, 304L and 316L. 2B stainless steel finishes are most commonly used in the petrochemical, industrial and food processing industries.

BA (Bright Annealed) - This bright, shiny finish is produced by annealing in an oxygen-free atmospheric condition following cold-rolling with highly polished rolls. The degree of brightness can vary depending on the grade, gauge and annealing conditions. Common grades of BA material are 304 and 430. When buying a BA, be sure to specify its end-use. This information is critical to ensuring that you receive the best bright surface for your application. BA material is available only up to about .075” thick. Due to the process, a light gauge BA material may be brighter than 16 gauge BA.

No.8 Finish - It is produced in the same manner as the No. 7 finish except that the buffing is continued for an additional five to ten minutes. In comparison to a No. 7 finish, the grit lines are much less visible, but they can be seen if the finish is examined closely. The resulting finish is mirror-like but not a perfect mirror.

If you are unsure of what finish is best for your application, we highly recommend that you contact us (Email: sales(at)sakysteel.com) . As specialists, we will ensure that your finish is the correct one.

Process Service

 

Application

Packing & Delivery

Stainless steel strip Detail Package:

--Standard Package: Cardboard encase the ends of the coil , with core and out steel edge protection. ( No Cardboard was accepted according to customers’ instructions)
--Strips are wrapped with metal strapped and packed in strong wooden pallets.
--Special customized package is acceptable upon customers’ request

Pre-sale Service.

1.Help you to choose the products.
2.Provide samples for confirmation
3.Making the products according to
your requirement..

Sales Service.

1.A variety of certification test
2.Help you to make the method statement and the details of the production process.

After -Sales Service.

1. Our Customer service team is on 
standby at all times,and if you need any help.
2.If you have any question ,you can
contact us

Certifications

 

About Sakysteel

SakySteel Co.,Ltd is located in Jiangsu Province. The company was founded in 1995. Now the company covers totally 220,000 square meters . The company has a total employee of 150 out of whom 120 are professionals .The company has been continually expanding itself ever since it's founded . Now the company is a ISO9001:2000 certified company and has been continually awarded by the local government .
The company through investment steel smelting and forging factory resume stability, a wide range of available resources.Main produce and process stainless steel bar/rod/shaft/profile,stainless steel pipe/tube, stainless steel coil/sheet/plate/strip, stainless steel wire/wire rod/wire rope.Our company supply products from SAKY,TISCO, LISCO, BAOSTEEL, JISCO and so on.We can customize non-standard special stainless steel products with high quality with short time. Our products used to chemical treatment equipments, chemicals tanks, petrochemical equipment and press plates. It is also used in railway coaches, roof drainage products, storm door frames, food machinery and tableware.

Quality Control

Contact Us