Japan TECLOCK Dele Manual Rubber Hardness Tester Constant Pressure Test Bench GS-615
 
Product number:
GS-615
 
product name:
Hardness tester

Applicable Hardness Tester Model:
A, B, E, A (old style),

After optional ZY-090, it can be used for TYPE C type (ASKER C), O type

After ZY-046 is selected, it can be used for TYPE D, ASTM C, DO, JIS C (old models)

 

product manual:
 

Install the hardness tester on the manual measuring table, install the load required by the JIS standard, and manually measure the hardness of the product.
The use of cams makes the operation simple and at the same time cost-effective.
Using a test bench, the indenter can be in close contact with the workpiece, and the measurement is accurate.
The constant pressure of type A and type E hardness tester is 1kg, and the type D hardness tester needs to be equipped with ZY-046 5kg load. Digital hardness tester GSD series, ZY-090 1kg load is required.
 
 
Product Usage:
 

A tool used to hold and assist in the measurement of the hardness tester.
Technical Parameters

Measure the load		Pack heavy model	Adapt to the type of hardness tester
1kg weight	Pointer type	ZY-087 (standard configuration)	A,B,E,JA,SRIS C, O
	Digital	ZY-088 (optional)
5kg weight (4kg weight)		ZY-046	D, ASTM C, DO, old JIS C

 
 

quality

3.9kg

Dimensions

IS K 6301 standard rubber hardness tester TECLOCK from Japan
 
Product number:
GS-706N

Old type A hardness tester, single needle

Picture of Type A Probe:

product name:

Hardness Tester, Rubber Hardness Tester, Plastic Hardness Tester
 
product manual:

TECLOCK rubber hardness tester, in some cases, such as measuring uneven surface or narrow flat surface and deep bottom, can be accurately measured.
The product has digital display, pointer (double needle and single needle). 
Product Usage:

There are three general models of the hardness tester, A, D and C. When the A type is used for measurement, when the hardness is greater than 90, the D type is suitable. When the A type is unreasonable, and the hardness is less than 20, the C type is suitable. .
Type A is a rubber hardness tester for measuring general plastics.
Type E is a hardness tester for measuring soft plastics, such as sponge and soft rubber.
Type C is a durometer for rubber whose hardness is less than that of Type A.
Type D is a hardness tester for measuring height hardness. Such as hardness rubber, plastic hard rubber. If there is an unbalanced measuring surface, reduce the plane, for the irregular shape of the bottom of the concave and convex deep, can be measured well, digital display, easy to read the measured value.
Technical Parameters

model	Types of	Application/Material	Stylus shapeSpring load value
GS-703N	JIS C (old model)	Hard rubber	φ0.79 truncated cone 35°	980-44100mN （100-4500gf）
GS-703G	JIS C (old model) (pin type)	Hard rubber	φ0.79 truncated cone 35°	980-44100mN （100-4500gf）
GS-706N	JIS A (old model)	General rubber	φ0.79 truncated cone 35°	539-8385mN （55-855gf）
GS-706G	JJIS C (old model) (pin type)	General rubber	φ0.79 truncated cone 35°	539-8385mN （55-855gf）
GSD-706K	JIS A (old model)	General rubber	φ0.79 truncated cone 35°	539-8385mN （55-855gf）

Dimensions

IS K 6301 standard rubber hardness tester TECLOCK from Japan
 
Product number:
GS-706N

Old type A hardness tester, single needle

Picture of Type A Probe:

product name:

Hardness Tester, Rubber Hardness Tester, Plastic Hardness Tester
 
product manual:

TECLOCK rubber hardness tester, in some cases, such as measuring uneven surface or narrow flat surface and deep bottom, can be accurately measured.
The product has digital display, pointer (double needle and single needle). 
Product Usage:

There are three general models of the hardness tester, A, D and C. When the A type is used for measurement, when the hardness is greater than 90, the D type is suitable. When the A type is unreasonable, and the hardness is less than 20, the C type is suitable. .
Type A is a rubber hardness tester for measuring general plastics.
Type E is a hardness tester for measuring soft plastics, such as sponge and soft rubber.
Type C is a durometer for rubber whose hardness is less than that of Type A.
Type D is a hardness tester for measuring height hardness. Such as hardness rubber, plastic hard rubber. If there is an unbalanced measuring surface, reduce the plane, for the irregular shape of the bottom of the concave and convex deep, can be measured well, digital display, easy to read the measured value.
Technical Parameters

model	Types of	Application/Material	Stylus shapeSpring load value
GS-703N	JIS C (old model)	Hard rubber	φ0.79 truncated cone 35°	980-44100mN （100-4500gf）
GS-703G	JIS C (old model) (pin type)	Hard rubber	φ0.79 truncated cone 35°	980-44100mN （100-4500gf）
GS-706N	JIS A (old model)	General rubber	φ0.79 truncated cone 35°	539-8385mN （55-855gf）
GS-706G	JJIS C (old model) (pin type)	General rubber	φ0.79 truncated cone 35°	539-8385mN （55-855gf）
GSD-706K	JIS A (old model)	General rubber	φ0.79 truncated cone 35°	539-8385mN （55-855gf）

Dimensions

Dongguan Gaotengda Precision Tools Co., Ltd.
[Agent CHEVALIER Taiwan Fuyu Precision Surface Grinding Machine CNC Grinding Machine]
FSG-12_16_20 series_new energy industry_lithium battery coating nozzle
FVGCseries_TC_20210518_V4 New Energy Industry
SMART-B818III_New Energy Industry_Ultrasonic Welding Head
Taiwan Fuyu CHevalIER CNC surface grinder, large water grinder
Vertical machining center, 5-axis machining center QP5X-400
Multifunctional CNC lathe, CNC lathe Taiwan Qiaojia JAGURA cylindrical grinder, centerless grinder
Japan RS-Japan Ultrasonic High Speed Spindle
Korea KTC fine hole electric discharge machine, punching machine
Italy DELTA vertical grinder LC-400, LC-500
Swiss DAMA Sharpener MM-12
Japan AMADA turning and milling compound processing machine
Japan Mitsui MITSUI surface grinder, grinder
Japan KIRA Kira machine tool KPC-30b, PCV-30
Japan Kondo circular grinding CKG series, ASZ series, UGK series, CTW series