High Purity Double Thread SiC Heating Element Oxidation Resistance Long Service Life

 

Silicon Carbide Heating ElementDescription

 

Silicon Carbide Heating Element can be installed and replaced while the tin bath is operation. The heaters can be installed through the side-seal, or through the side of the bath roof, and are commonly used to extend campaign lives, where conventional elements in the side zones have been broken, and insufficient power is available.

 

Silicon Carbide Heating Element Advantages

 

High purity raw materials;

High structural density;

Slow aging;

Maximum temperature being up to 1500℃ (2732°F);

Easy to be installed and replaced.

 

Types and Applications of Silicon Carbide Heating Element

1. SW (Standard)

SW Silicon Carbides are used in applications ranging in temperature from 600°C up to 1400°C in both air and controlled atmospheres. Although the type of atmosphere used will determine the maximum recommended element temperature. This kind of silicon carbide elements can be mounted either vertically or horizontally.

2. U-TYPE

U shape Silicon Carbide is consists of two silicon carbide rod with same diameter. Each rod has both hot zone and cold end with identical resistance. Two rods are connected by the low resistance SiC. Also the connector could be used as holder according to different requirements.

3. W-TYPE

3-phase elements are available in 2 different types: SGC (Dumbbell), SGD(Standard).

These elements are self-bonded silicon carbide formed by re-crystallization of silicon carbide at high temperature. It consists of three high-purity silicon carbide rods connected at one end by a silicon carbide crossbar. SGC elements are designed for vertical installation in standard float glass bathes and SGD elements for horizontal installation. They can be connected directly on three-phase power supply and is a one-side terminal type which permits drawing out the terminals from the roof of the furnace.

4. Single Spiral Silicon Carbide and Double Spiral Silicon Carbide:

They are made from silicon Carbide powder, and have two shapes: single and double sprial silicon carbide heating element. They are widely used in all kinds of kilns and furnaces.

Physical property of SIC heating element

specific gravity	2.6~2.8g/cm³	bend strength	>300kg
hardness	>9MOH’S	tensile strength	>150kg/cm³
porosity rate	<30%	radiance	0.85

 

Recommended surface load and Influences to Surfaces of the Elements in Different Operating TemperatureS

atmosphere	Furnace Temperature(°C)	Surface Load(W/cm2)	The influence on the Rod
Ammonia	1290	3.8	The action on SiC produces methane and destroys the protection film of SiO2
Carbon dioxide	1450	3.1	Corrode SiC
Carbon monoxide	1370	3.8	Absorb carbon powder and influence the protection film of SiO2
Halogen	704	3.8	Corrode SiC and destroy the protection film of SiO2
Hydrogen	1290	3.1	The action on SiC produces methane and destroys the protection film of SiO2
Nitrogen	1370	3.1	The action on SiC produces insulating layer of silicon nitride
Sodium	1310	3.8	Corrode SiC
silicon dioxide	1310	3.8	Corrode SiC
Oxygen	1310	3.8	SiC oxidized
Water-vapor	1090-1370	3.1-3.6	The action on SiC produces hydrate of silicon
Hydrocarbon	1370	3.1	Absorb carbon powder resulted in Hot pollution

 

Notice for using and installing:

1. Heater should be protected against damp during storing or installing to ensure the performance of the heater.

2. In order to be sure of well-distributed lod of each and groups, heater should be divided before assembling. The tolerance of the resistance of each one cannot exceed by 10% each other.

3. Heater is hard and brittle, please be careful when assembling and maintaining so as to avoid damage.

4. When operating the electric furnace at the beginning, the voltage should be increased slowly and cannot be fully loaded at once. Otherwise the larger current will be resulted in the damage of heater.

5. When heater is damaged and need to be changed, the resistance of new one should follow the increasing resistance. If many are damaged or resistance increased too much, heater should be changed.