System status
At startup:
Before the hydraulic and lubrication system components are delivered to the assembly site, their internal oil circuits and surfaces should be coated with anti-corrosion coatings compatible with fire-resistant fuel. If the manufacturer conducts pre testing on the equipment, it is recommended to use a corrosion-resistant phosphate ester for quality control inspection to provide corrosion protection.
The storage period on site should be as short as possible (it is recommended that the long-term limit is one year), and parts coated with phosphate ester should be placed indoors and sealed as much as possible. Because this liquid is sensitive to humidity. If acceptance inspection is carried out, the equipment should be immediately resealed and some desiccant added afterwards.
To prevent dirt from entering during assembly, it is important to minimize the number of times the system is opened and maintain a clean working area. Careful prevention of pollution at this stage is very beneficial for the commissioning process and also contributes to future trouble-free operation.
When switching from mineral oil:
The system must be flushed according to the manufacturer's requirements until the specified cleaning level is reached. This process is very important because a small amount of mineral oil can have a negative impact on the foaming performance of the fuel. Detailed steps can be found in<System Flushing>.
System maintenance:
If the system using fire-resistant fuel is not properly maintained, no matter which type of fire-resistant fuel is used, it cannot operate satisfactorily*** The key to good fuel resistance performance is to regularly check all filters and vents; Minimize leakage of steam and coolers as much as possible; Prevent air leakage from the sealing area, etc.
Efforts should be made to minimize the leakage of fire-resistant fuel outside the system, in order to reduce the cost of replenishing and cleaning up spilled fire-resistant fuel.
Initial state of fire-resistant oil
The production of fire-resistant oil meets the requirements of relevant regulations*** The key to good fuel resistance performance is to regularly check all filters and vents; Minimize leakage of steam and coolers as much as possible; Prevent air leakage from the sealing area, etc. Efforts should be made to minimize the leakage of fire-resistant fuel outside the system, in order to reduce the cost of replenishing and cleaning up spilled fire-resistant fuel.
If the fire-resistant oil cannot meet the specified initial requirements, it will result in violating the warranty conditions of the equipment and reducing the service life of the fire-resistant oil.
System operating temperature
The important factor affecting the lifespan of fire-resistant oil is temperature. The average operating temperature of fire-resistant oil is usually controlled between 50 ℃ and 65 ℃. However, a temperature of * * * can also be used, but measures should be taken to prevent moisture and increased acidity, otherwise the water in the fuel tank will condense. This is even more true if the equipment is shut down regularly (such as every week * * *). In this case, it is recommended to regularly check the water content, and if necessary, start the particle processing system and/or dehydration device throughout the entire shutdown period.
Although the average temperature is not high, there may be local hotspots, such as on valves, bearings, hot surfaces, gas seals, and gearboxes. In these areas, the fire-resistant oil may undergo oxidation and/or thermal decomposition, and under * * * conditions (such as exceeding 150 ℃), it can thicken and produce deposits.
During cold start, use a fuel tank heater to reduce the viscosity of the fire-resistant oil. The power of the heater must be appropriate, and the fire-resistant oil should be circulated on the surface of the heater as much as possible throughout the entire heating period to prevent local overheating of the fire-resistant oil and the formation of deposits on the surface of the heater.
National minimum batch per barrel
Solemnly promise: Official certification, original and genuine, with a penalty of ten for every fake product, and no refund for dissatisfaction!
Our company promises that due to our local business, with over a dozen trucks and a large warehouse, in order to better serve customers, salespeople will track the movements of each batch of goods at any time and contact buyers at any time, so that buyers can receive and use goods with peace of mind!
For detailed information, please contact our company: Mr. Zhao 17316311889
What are our services?
1. We can search for anti-counterfeiting products for you.
2. We can issue a 13% value-added invoice for you.
3. We can provide you with product factory inspection reports and quality assurance certificates, as well as MSDS reports on product material safety.
4. We can collect samples free of shipping for you.
5. Free shipping within Guangdong Province.
6. Order more than ten tons of products at once, clean the machinery for free, and change the oil for free.
7. The product is returned or exchanged unconditionally without opening the packaging.
8. During the product warranty period, you can receive free technical support from the manufacturer!
9. Kind reminder: Picture shooting and physical products are the same. We have taken several physical pictures of each product, and customers can place orders based on the physical pictures. The prices vary depending on the physical pictures, and they are all at a one go price. Please do not bargain. It is our honor to help customers choose a good product; You are trustworthy!!!
10. Authorization commitment for electric fire-resistant fuel: We only sell genuine products! Authentic! Authentic! Say important things three times!!!