Product Name

MSK-AFA-I Automatic Coater

Product Model

MSK-AFA-I

Installation Conditions

This equipment is required to be used at an altitude of 1000m or less, a temperature of 25℃±15℃, and a humidity of 55%Rh±10%Rh.

1. Water: N/A

2. Electricity: AC220V 50Hz, must have good grounding

3. gas: N/A

4. Workbench: size 800mm×600mm×700mm, bearing more than 200kg

5. Ventilation device: no need

Main Parameters

(specification)

1. Power supply: AC 220V, 50HZ

2. Total power: 50W

3. Coating speed: 10mm/s-100mm/s adjustable

4. Coating travel distance: 10mm-290mm

5. Vacuum aluminum plate / chuck: 360mm×200mm (length×width)

6. Vacuum size (max): 300×150mm (length×width)

7. Film applicator: 150mm micron adjustable type (other sizes can be selected), the adjustable range is 0.01mm-5mm

8. Film thickness accuracy: ±0.01mm

Product Dimension and Weight

Dimension: 500mm×330mm×223mm

Weight: 50kg

• 5 - 100 mm/sec variable
• Accuracy: 10mm/sec

• 10 - 550 mm adjustable by using the Adjustable Position Switch

• 250mm(W) x 550mm(L)

• Vacuum chuck made of Aluminum alloy with < 1 mm holes. The hole distance is around 14.8 mm. 

•          120L/min Oilless Vacuum Pump
•     

• 250 mm width Micrometer Adjustable Film Applicator is included, with adjustable thickness from 0.01 - 5 mm
• Traverse Pusher is included for pushing the doctor blade to ensure constant speed coating
• Note:  Thinnest film can be achieved is > 10 micron

• Vacuum Chuck : 600mm(L) x 300mm(W)
• Product: 805mm(L) x 430mm(W) x 223mm(H)

           Click the pic for more detail.

• CE certified
• NRTL / CSA certification is available upon request at an extra cost.

• Pic.1 and 2 show coated cathode and anode for Li-Ion batteries. Please click here to see how to 
• It is recommended to operate the coater under a fume hood. (Click Pic.3 for detail.)
• You need a vacuum mixer to  make uniform coatings (Click Pic.4 for detail.)
• You may need a Slurry Viscosity Tester to make coatings consistent (Click Pic.5 for detail.)
• You may need a vacuum oven to dry the films and remove the binder after coating. (Click Pic.6 for detail.)
• Rolling pressing is necessary to ensure good density and adhesion of electrode materials to the current collector substrate after coating. Please select a rolling press from here. (Click Pic.7 for detail.)

                      
Pic.1                   Pic.2                      Pic.3               Pic.4                    Pic.5                   Pic.6                       Pic.7                             

MSK-AFA-I

MSK-AFA-III-HB         

MSK-AFA-III-110/220  

MSK-AFA-III-HB
-UV-110/220      

MSK-AFA-IIIT-HBT

No Heating

Bottom Heating 110/ 220VAC  850W 120ºC 

Top Heating
1.2KW, 100ºC

Top UV (WL: 365nm)
Bottom Heating, 1kW, 120ºC

Top and Bottom Heating
110/220V, 2.3 kW, 120ºC

• Power adaptor: Input 100-240VAC, Output 24VDC

• 10 - 100 mm/sec variable
• Accuracy: ± 5-10 mm/sec

• Standard Package: 320mm(L) x 100mm(W) due to the width and occupied area of the 100mm applicator
• S ested Maximum: 350mm(L) x 180mm(W)  Reduced width to avoid slurry spilling off the vacuum bed
• Length 10 - 350 mm adjustable by using Adjustable Position Switch

• Vacuum chuck made of Aluminum alloy with < 1.0 mm hole
• Vacuum Chuck Dimensions: 365mm(L) x 200mm(W)  （ 14“L x 8"W )
• Note: You may order a glass plate to coat slurry on a porous substrate at the link below
•          

• Maximum: 350mm(L) x 180mm(W)  Reduced width to avoid slurry spilling off the vacuum bed
• Length 10 - 350 mm adjustable by using Adjustable Position Switch

• One 100 mm width micrometer adjustable film applicator is included (thickness adjustable from 0.01 - 3.5 mm)
• For coating film less than 10 microns, please order a fixed thickness coating bar (click Pic left-1 below)
• Travel Pusher and waste plates are included for pushing the Film Applicator (see pic below-middle)
• Please click here to find Film Applicators with different widths at extra cost

                     Note:  Thinnest film that can be achieved is > 10 microns

• NO vacuum pump is included.  You may use your own pump or select a pump in the optional bar. 
• You may order a 120L/min Oilless Vacuum Pump 

• The vacuum control power switch is located on the front panel, and the power plug ( female ) is built into the back of the machine to connect an optional vacuum pump
• The pump connector is a compression-type 8mm O.D tube fitting which is located on the back panel (see pic below). An 8mm Dia. x 4ft polyurethane tube is included
•     

• Pre-installed on the top cover
• Built-in digital temperature controller with an accuracy of +/-1°C
• Suspension support helps open the cover easily and safely
• Max. Heating Temp.: 100°C
• Note: In order for faster and uniform heating,  please preheated the vacuum chunk to 60- 70°C before coating, and keep heating during coating, then close the cover and increase the temperature to ~100°C after coating

• CE Certificate 
• NRTL or CSA certification is available upon request 

• Pic.1 and 2 show coated cathode and anode for Li-Ion batteries. Please click here to see how to coat an electrode sheet.
• It is recommended to operate the coater under a fume hood. (Click Pic.3 for detail.)
• You need a vacuum mixer to remove air bubbles inside the slurry and to make uniform coatings (Click Pic.4 to order)
• You may need a Slurry Viscosity Tester to make coatings consistent (Click Pic.5 for detail.)
• You may order a Hybrid Film Applicator of slot die & doctor blade to test slot die coating. ( Click Pic 6 to order )
•   Pic. 1    Pic. 2Pic. 3 Pic. 4 Pic. 5        Pic. 6