FAQ

Q1:

How to operate the leather embossing machine correctly?

An embossing machine is a device for embossing clothing, paper, plastic, and leather. So, how do we proceed with this? At the same time, what are its characteristics?

A1:

1. First turn on the three-phase power main switch, and then turn on the power switch on the control box on the side of the machine. If there is a high-cycle switch, leave it off for the time being. Then turn on the electric heating power switch. At this time, the vacuum tube and the hot mold begin to preheat. hot.

2. Add insulation to the lower mold, install the upper mold on the upper end, press the mold trial switch, and start adjusting the joint position of the upper and lower molds. If the lower joint is poor, move the lower mold. If the level is not consistent, adjust the four sides of the upper mold. Pillars.

3. After the mold is adjusted, adjust the three time controllers (if it is a foot-operated machine, there is only high-cycle welding time). The descending time is the time from the upper mold to running to the lower mold. The welding time is the output time and cooling time. , that is, the curing time. The above three times need to be applied flexibly and there is no fixed value.

4. If it is the first time to adjust the mold, it is necessary to adjust the spacing of the co-tuning to the widest.

5. If the above operation has lasted for more than 10-15 minutes and the temperature has reached the required level, turn on the high-cycle switch and start the operation test.

The electronic heating controller is mainly used to heat the upper and lower templates, and the male and female molds are installed on the heating work plate. With a certain amount of pressure, the purpose of embossing can be completely achieved.

Q2:

Detailed explanation of leather embossing process?

A2:

1. Introduction
Leather is a commonly used material that is widely used to make shoes, handbags, belts and other clothing and accessories. Among them, leather embossing is an elegant decoration technology that can add unique textures and patterns to leather products, improving the aesthetics and texture. Let’s take a closer look at the leather embossing process.
2. Principle
The principle of leather embossing is to use the pressure and heat of an embossing machine (also called a creasing machine) to process the leather and press patterns and patterns onto the leather surface to achieve a decorative effect. Before leather is embossed, the leather needs to be soaked in water to make it soft and elastic.
3. Process
The leather embossing process is mainly divided into the following three steps:
1. Laying the leather
Lay the leather soaked in water on a workbench and use a scraper to remove excess water until it becomes flat. It is important to note that the surface of the leather should be even without any wrinkles or damage.
2.Choose the pattern
According to the required flower shape and pattern, select the corresponding embossing machine and embossing mold. Different molds have different shapes and sizes and can produce different patterns and patterns. Before embossing, the mold needs to be hot-knocked to make the surface reach the appropriate temperature to ensure the embossing effect.
3.Embossing processing
Place the hot-beaten embossing mold on the embossing machine, place the paved leather on the mold, and after adjusting the pressure and temperature, start the embossing machine and perform embossing processing. Once processing is complete, the leather is removed, dried and processed further.
4. Tools
The tools required for leather embossing mainly include: embossing machine, embossing mold, scraper, etc. Among them, the embossing machine is the main tool for leather embossing, and its pressure and temperature need to be adjusted by the machine to ensure the accuracy and stability of the process. The embossing mold is the key equipment for pressing patterns and patterns onto the leather surface. Its selection and use need to be matched according to the desired decorative effect.
【in conclusion】
Leather embossing is a common leather decoration technique that adds beauty and texture to leather products. Through the introduction of tamprinter, customers can understand the principles, processes and tools of leather embossing, master basic embossing techniques and precautions, and provide help in producing exquisite leather products with unique patterns.

Q3: 

Cleaning and lubrication of leather embossing machine?

A3:
After the leather embossing machine is used for a period of time, oil stains and dust will accumulate, so it needs to be cleaned and lubricated. Specific steps are as follows:
1. First, turn off the power of the leather embossing machine and disconnect the power plug.
2. Use detergent and cloth to wipe the surface of the leather embossing machine. Be careful not to use detergents containing acid and alkali ingredients to avoid damaging the surface of the machine.
3. After cleaning, use lubricant to lubricate the machine bearings, transmission sprockets and other parts to extend the service life of the machine and avoid noise during operation.

Q4:
How to clean and lubricate a leather embossing machine?
A4:
After the leather embossing machine is used for a period of time, oil stains and dust will accumulate, so it needs to be cleaned and lubricated. Specific steps are as follows:
1. First, turn off the power of the leather embossing machine and disconnect the power plug.
2. Use detergent and cloth to wipe the surface of the leather embossing machine. Be careful not to use detergents containing acid and alkali ingredients to avoid damaging the surface of the machine.
3. After cleaning, use lubricant to lubricate the machine bearings, transmission sprockets and other parts to extend the service life of the machine and avoid noise during operation.
Q5:
How to adjust and replace accessories of leather embossing machine?
A5:
The leather embossing machine is used frequently, so it is necessary to regularly check and adjust the working condition of the machine parts, and replace worn parts in time to ensure the normal use of the machine.
1. First, check all parts of the leather embossing machine, including flower wheels, pressing wheels, positioning stakes, cutters, etc., to see if they are in normal working condition.
2. For abnormal situations that occur during the operation of the machine, such as noise, insufficient pressure, etc., it is necessary to promptly check and adjust the relevant parts of the machine.
3. If machine parts are severely worn or damaged, they need to be replaced in time to avoid irreversible failure.
Q6:
How to store and maintain leather embossing machines
A6:
1. When the leather embossing machine is not used or stored for a long time, the machine needs to be cleaned and sealed with plastic sheeting to prevent the machine from getting damp and rusting.
2. In addition, it is necessary to regularly check whether the power supply voltage and connection lines of the leather embossing machine are normal to ensure that misoperation or failure can be solved in time.
In short, the care and maintenance of the leather embossing machine is very important during daily use. Only regular cleaning, lubrication, adjustment and replacement of accessories can extend the service life of the machine, improve production efficiency and better meet user needs.