Order number MN-06-310-HN MN-06-311-HN
Please complete
according to order
code.
Function
3/2-way, normally closed 3/2-way, normally closed
single solenoid, air spring return single solenoid, spring return
Connection G 1/4 at 1 and 3; flange to NAMUR at 2
Nominal size 6 mm
Flow rate 750 Nl/min (0.762 Cv)
Pressure range 2 . . . 10 bar 2) (29 … 145 psi)2) 3 . . . 10 bar 2) (43 … 145 psi)2)
Actuating on 13 ms
force at 6 bar off 16 ms
Temperature
range – 10 °C . . . + 70 °C (+ 14 °F … + 158 °F)
Materials Body: Al (anodized), Seals: NBR and POM, Inner parts: Al, stainless steel, brass
Degree of
protection IP 65 according to EN 60529
Weight 0.320 kg (0.705 lb.)
Standardized valve series
3/2-way
acc. to NAMUR, 750 Nl/min (0.762 Cv)
Technical data for series
MN-06
5.020 Subject to change
Design and function
Spool valve for single acting actuators switched by an electrical signal.
The exhaust air is guided into the spring chamber of the actuator. The standard coil, plug socket (see page
5.024), locating pin, screws and seals are included.
For outdoor applications or in areas with high humidity use coil 23-SP-011-1 or 23-SP-012-1 (see page 5.120).
Please specify required control voltage when ordering.
Valves of this series are available in explosion proof design in accordance with 94/9/EG (ATEX). For further
details see chapter 12 of this catalogue.
2) max. 8 bar (max. 116 psi) at 2.2 W and 2.5 W.
Order code MN-06-310-HN-142
Series
and
function
Coil options
1) When the valve is requested without the plug socket, the first digit of the order code for standard coils must be changed
from 1 to 4. For optional plug sockets see page 5.024.
Standard coil 1)
(with plug socket 28-ST-01)
141 = 12 V DC, 4.2 W
142 = 24 V DC, 4.2 W
152 = 24 V AC, 7/4 VA
156 = 115 V AC, 7/4 VA
157 = 230 V AC, 7/4 VA
161 = 12 V DC, 2.2 W 2)
162 = 24 V DC, 2.2 W 2)
Without coil and plug socket
570 = Power consumption 4.2 W, 7/4 VA
560 = Power consumption 2.2 W 2)
Coils with M12 connector and LED
O42 = 24 V DC, 4.8 W
O62 = 24 V DC, 2.5 W2)
Coils with higher humidity resistance
742 = 24 V DC, 4.2 W without plug socket
757 = 230 V AC, 7/4 VA without plug socket
842 = 24 V DC, 4.2 W (with plug socket 28-ST-01)
857 = 230 V AC, 7/4 VA (with plug socket 28-ST-01)
Order number MN-06-510-HN MN-06-511-HN MN-06-520-HN MN-06-530-HN
Please complete
according to order
code.
Function 5/2-way 5/2-way 5/2-way 5/3-way
air spring return spring return double solenoid center position closed
Connection G 1/4 at 1, 3, 5; flange to NAMUR at 2 and 4
Nominal size 6 mm
Flow rate 750 Nl/min (0.762 Cv) 650 Nl/min (0.661 Cv)
Pressure 2 . . . 10 bar 2) 3 . . . 10 bar 2) 2 . . . 10 bar 2) 3 . . . 10 bar 2)
range (29 … 145 psi) (43 … 145 psi) (29 … 145 psi) (43 … 145 psi)
Actuating on 13 ms 12 ms on 13 ms
force at 6 bar off 16 ms off 15 ms
Temperature
range – 10 °C . . . + 70 °C (+ 14 °F … + 158 °F)
Materials Body: Al (anodized), Seals: NBR and POM, Inner parts: Al, stainless steel, brass
Degree of
protection IP 65 according to EN 60529
Weight 0.320 kg (0.705 lb.) 0.460 kg (1.014 lbs.)
Standardized valve series
5/2- and 5/3-way
acc. to NAMUR, 750 Nl/min (0.762 Cv)
Technical data for series
MN-06
Subject to change 5.021
5
Design and function
Spool valve for double acting actuators switched by an electrical signal.
The standard coil, plug socket (see page 5.024), locating pin, screws and seals are included.
For outdoor applications or in areas with high humidity use coil 23-SP-011-1 or 23-SP-012-1 (see page 5.120).
Please specify required control voltage when ordering.
Valves of this series are available in explosion proof design in accordance with 94/9/EG (ATEX). For further
details see chapter 12 of this catalogue.
2) max. 8 bar (max. 116 psi) at 2.2 W and 2.5 W.
Order code MN-06-510-HN-142
Series
and
function
Coil options
1) When the valve is requested without the plug socket, the first digit of the order code for standard coils must be changed
from 1 to 4. For optional plug sockets see page 5.024.
Standard coil 1)
(with plug socket 28-ST-01)
141 = 12 V DC, 4.2 W
142 = 24 V DC, 4.2 W
152 = 24 V AC, 7/4 VA
156 = 115 V AC, 7/4 VA
157 = 230 V AC, 7/4 VA
161 = 12 V DC, 2.2 W 2)
162 = 24 V DC, 2.2 W 2)
Without coil and plug socket
570 = Power consumption 4.2 W, 7/4 VA
560 = Power consumption 2.2 W 2)
Coils with M12 connector and LED
O42 = 24 V DC, 4.8 W
O62 = 24 V DC, 2.5 W2)
Coils with higher humidity resistance
742 = 24 V DC, 4.2 W without plug socket
757 = 230 V AC, 7/4 VA without plug socket
842 = 24 V DC, 4.2 W (with plug socket 28-ST-01)
857 = 230 V AC, 7/4 VA (with plug socket 28-ST-01)
Standardized valve series
3/2- and 5/2-way
acc. to NAMUR, 750 Nl/min (0.762 Cv)
Dimensions for series
MN-06
MN-06-310-HN, MN-06-311-HN
MN-06-510-HN, MN-06-511-HN
5.022 Subject to change
1 = pressure inlet
2, 4 = outlets
3, 5 = exhausts
(7) = manual override (detent)
can be repositioned by 180h
(8) = plug socket can be
repositioned by 180h
(9) = solenoid coil can be
repositioned 4 x 90h
1 = pressure inlet
2 = outlet
3 = exhaust
(7) = manual override (detent)
can be repositioned by 180h
(8) = plug socket can be
repositioned by 180h
(9) = solenoid coil can be
repositioned 4 x 90h
Subject to change 5.023
Standardized valve series
5/2- and 5/3-way
acc. to NAMUR, 750 Nl/min (0.762 Cv)
Dimensions for series
MN-06
1 = pressure inlet
2, 4 = outlets
3, 5 = exhausts
MN-06-520-HN, MN-06-530-HN
5
(7) = manual override (detent) can be repositioned by 180h
(8) = plug socket can be repositioned by 180h
(9) = solenoid coil can be repositioned 4 x 90h
Accessories for
standardized valve series,
NAMUR, series MN-06
Accessories for series
MN-06
5.024 Subject to change
Solenoid coils, actuators
Plug sockets
User information
Low power consumption coils (2.2 W or 2.5 W) are for pressures up to 8 bar (116 psi) only. Valve actuator 23-R-012
is required. The actuator 23-R-012 is nickel plated. Make sure that the coils with the right power consumption
are used.
When using explosion proof coils the dimensions of the corresponding valve change.
For outdoor applications or in areas with high humidity use coil 23-SP-011-1-… or 23-SP-012-1-… (see page 5.120).
The following types are available on request
Coils and sockets with contacts according to DIN EN 175301-803 type B (U-form).
Plug sockets with molded cable.
Standard plug socket
28-ST-01
page 4.281
Plug socket with LED
28-ST-04-…
page 4.281
Plug socket with LED
and circuit protection
28-ST-06-…
page 4.281
Plug socket with LED,
circuit protection and cable
28-ST-06-K3-…
page 4.281
Standard
actuator
23-R-011
Low power
actuator
23-R-012
Standard coil
23-SP-011-…
page 4.280
Coil with 2.2 W
power consumption
23-SP-012-…
page 4.280
Coil with M-12 plug
connection, 4.8 W, LED
and circuit protection
23-SP-011-5-O12
page 4.280
Coil with M-12 plug
connection, 2.5 W, LED
and circuit protection
23-SP-012-5-O32
page 4.280
Valves with explosion
proof actuator see
chapter 12.
Speed regulation plates for
standardized valve series,
NAMUR, series MN-06
Accessories for series
MN-06
Speed regulation plates
Speed regulator plate for
single acting actuators
MN-063-DR
page 5.027
Speed regulator plate for
double acting actuators
MN-065-DR
page 5.027
Subject to change 5.025
Other single elements: 20-MN-06-01
NAMUR seals disc to convert a 5/2-way valve into a 3/2-way function.
Speed regulator plate for 5
single acting actuators
MN-063-DRS
page 5.026
Speed regulator plate for
double acting actuators
MN-065-DRS
page 5.026
Accessories for NAMUR valves
Speed regulation plates
5.026 Subject to change
Order number MN-063-DRS MN-065-DRS
Function Speed regulation plate for single Speed regulation plate for double
acting actuators acting actuators
Nominal size 4 mm
Nominal flow
controlled flow direction 0 . . . 180 Nl/min (0 … 0.183 Cv) 0 . . . 240 Nl/min (0 … 0.244 Cv)
free flow direction 235 Nl/min (0.239 Cv) 250 Nl/min (0.254 Cv)
Temperature range – 10 °C . . . + 70 °C (+ 14 °F … + 158 °F)
Materials Body: Al, Inner parts: brass, Seals: NBR and PU
Weight 0.330 kg (0.727 lb.) 0.285 kg (0.628 lb.)
Technical data and dimensions for series
MN-063-DRS, MN-065-DRS
MN-063-DRS
MN-065-DRS
Design and function
The locating pin, screws and seals are included.
Valves of this series are available in explosion proof design in accordance with 94/9/EG (ATEX). For further
details see chapter 12 of this catalogue.
The unit can only be adjusted with a screw driver.
MN-063-DRS MN-065-DRS
Accessories for NAMUR valves
Speed regulation plates
Subject to change 5.027
5
Order number MN-063-DR MN-065-DR
Function Speed regulation plate for single Speed regulation plate for double
acting actuators acting actuators
Nominal size 4 mm
Nominal flow
controlled flow direction 0 . . . 180 Nl/min (0 … 0.183 Cv) 0 . . . 240 Nl/min (0 … 0.244 Cv)
free flow direction 235 Nl/min (0.239 Cv) 250 Nl/min (0.254 Cv)
Temperature range – 10 °C . . . + 70 °C (+ 14 °F … + 158 °F)
Materials Body: Al, Inner parts: brass, Seals: NBR and PU
Weight 0.350 kg (0.772 lb.) 0.305 kg (0.672 lb.)
Technical data and dimensions for series
MN-063-DR, MN-065-DR
MN-063-DR
MN-065-DR
Design and function
The locating pin, screws and seals are included.
Valves of this series are available in explosion proof design in accordance with 94/9/EG (ATEX). For further
details see chapter 12 of this catalogue.
MN-063-DR MN-065-DR
Accessories
Solenoid coil with higher humidity resistance
Solenoid coil with pin distance of 11 mm.
This coil is designed for outdoor applications in high humidity environments.
5.120 Subject to change
Other voltages on request.
Order number 23-SP-011-1-711 23-SP-011-1-712 23-SP-011-1-722 23-SP-011-1-726 23-SP-011-1-727 23-SP-012-1-732
Standard voltages 12 V DC 24 V DC 24 V AC 115 V AC 230 V AC 24 V DC
Power consumption 4.6 W 4.8 W 7/4 VA 2.5 W
Degree of protection IP 65 according to VDE 0470 / EN 60529, with connected plugs and additional O-rings
Duty cycle 100 % continous operation
Material Duroplast
Temperature range – 20 hC . . . + 50 hC
Voltage tolerance ± 10 %