We can OEM flame treatment guns according to customer order. 

Used as flame treatment of PP or PE ,PET, METAL materials printed, so that the printing ink better adhesion. Advanced and unique part of the design of the fire-breathing mouth of the flame gun, flame stability, long life, is not blocked, the flame does not float! High fuel efficiency can be installed on the machine can also be used alone. Division is designed for custom-made by some well-known companies such as automobile bumpers, stereo speakers, silicone rubber, turnover box, flame treatment equipment, Seiko produced up to 1.6 m of the flame spray gun, high efficiency, high stability.Welcome call us!

Specification:

1.The length of the gun is 250mm, the actual length of the fire is 200. The price of EXW is  300 dollars. 

2.The length of the gun is 300mm, the actual length of the fire is 250mm. The price of EXW is 350 dollars. 

3.The length of the gun is 200mm, the actual length of the fire is 150mm. The price of EXW is 250 dollars. 

Flame-processor works and the scope of application:

Most of the flame processor is used in PP, PET, PE plastic. We often give some of the electronic hardware manufacturers to make some special flame processor, such as Guangzhou Toyota plane turnover box flame processor, a famous brand stereo processor the speakers flame car bumpers, flame treatment, etc. PP, PE plastic non-polar polymer materials, chemical properties and stability, low surface tension, combined with synthetic resin added when opening agents, antistatic agents, anti-aging agent, it is difficult with the ink and a solid bond. In order to improve the printability of PP, PE plastic, must pass processing, so that the surface tension of not less than 3.8 × 10-2N / m.

Working principle: Flame treatment for the surface treatment of the small plastic container, and its principle is to make the plastic surface decontamination by high temperature and melt the film surface, to improve the surface adhesion of the ink.

The specific operation as follows: will be processed container into the gas flame, the flame length of the inner core control in 6 ~ 19mm, the top of the flame core from the surface of the container 6 ~ 25mm 0.1 ~ 1.0s, contact time, the rotation speed of 100 to 150 rpm / min. Flame contain-OH and-NH radicals in the excited state, the hydrogen bonding of the surface with a polymer plastic, and the introduction of some polar oxygen-containing groups, the occurrence of chain scission reaction, so that the surface wettability of plastic bonding can be improved.

Detection of treatment effect: the easiest way is to use the surface tension of the test pen testing. Selection of 3.8 × 10-2N / m surface tension of the specifications of the test pen, if the test stroke liquid marks evenly spread, not contraction, indicates that the treatment effect is better; liquid scar contraction, or liquid marks part of the contraction, in part not contraction, then the processing is not sufficient. 

Working principle and precautions:

1. The fire-breathing holes are 5 rows: the middle three rows are the flame main holes, and the two sides are the ignition sub-holes to prevent the compressed air pressure from being excessively extinguished, and the multi-layer design between the holes and the holes to meet the requirements of the customer flame length.

2. The gas source of the flame gun is compressed air and gas mixed gas. To improve the pressure of the gas, it is recommended that the gas supply valve be a medium pressure valve.

3. To reduce the noise during the working of the flame head, a silencer should be installed.

4. For safety reasons, it is recommended to use a shrink metal joint for the gas pipe joint, and a special 205 flame gun control valve for gas and air conditioning special products.

5, the flame gun has been installed with a seal to adjust the length of the flame, M5 stainless steel screws on the body of the flame gun can lock the seal.

6. Do not adjust the air and gas valves too much when the flame gun is ignited. For safety reasons, it is recommended to use a hand-held electronic igniter or an automatic ignition device.

7. When adjusting the flame, observe that the color of the flame is blue, and the length and color of the flame can be controlled by adjusting the gas and air valves.

8, if the gas is not pure enough, compressed air will cause the flame to have a red dot. Gas or compressed air should be replaced and filtered.

Operation method:There are two types of electronic ignition and manual ignition. Repair and maintenance editor When the flame gun body is too dirty, remove the air source and remove it with a cleaning agent and a stainless steel cloth. If the flame hole is partially blocked, you can tap the flame head when there is gas (be careful not to knock it hard) or turn off the air source to remove the hole through the gas. If the flame gun fire effect is not used, it can be returned to the factory for repair.

G3/8 teeth M5 or M6 stainless steel TAM-F250F 320mmX35mmX40mm Horizontal 0-250mm 10mm 5 G3/8 teeth M5 or M6 stainless steel TAM-F300A 355mmX25mmX40mm Horizontal 0-300mm 10mm 5