4E1/ETH protocol converter
| Model: | EB04 |
|---|---|
| Brand: | Ebang |
| Origin: | Made In China |
| Category: | Electronics & Electricity / Telecommunication & Broadcasting / Network Communications Equipment |
| Label: | 4E1/ETH converter , protocol converter , network converter |
| Price: |
-
|
| Min. Order: | 2 pc |
Product Description
Introduction:
EB04-FX serial interface converter used back multiplexing technology, transfer 10M/100M Ethernet data by using multi E1 channels. Realize convert between 1 to 4 E1 channels and Ethernet optical interface. It can transmit signal of E1 channel to Ethernet optical interface point to point, realize the connection of 1 to 4E1 channel and Ethernet.
Features:
( 1) Realize transparent transfer Ethernet data in 1-8 E1 channels ² 10M/100M Ethernet, full/half duplex self adapt, support VLAN.
(2) Ethernet support AUTO-MDIX( cross over and straight through self adapt)
(3)setting CRC alarm limitation to auto isolate lines with low transfer quality, single direction. When one direction error rate over limitation, disconnect only one direction, the other is not affected. Unbalance in two directions.
(4)Allow 1-4 E1 channels up to 10ms transfer delay. when the delay over the limitation, can stop transfer automatically.
(5)Having 2 loop back functions: E1 local loop, E1 external loop.
(6) Support Dynamic Ethernet MAC address(4096), having local address filter function.
(7)E1 interface compatible withITU-T G.703,G.704,and G.823. signaling slot not supported.
(8)E1 interface having internal clock resume circuit and HDB3 codec circuit.
(9)support E1 channel hot plug, and auto detect available E1 channels not pause the transmission.
(10)supporting 1-4 E1 channels customized configuration, auto detect the number of E1 channels and select the available E1 at reset.
(11) E1 Support 75Ω/unbalance impedance or 120Ω/balance for order
(12) support reset remote system from local system.
(13)having Ethernet monitor auto reset function.
(14)SNMP for option in chassis installation or built-in standalone
Technical Parameter:
E1 Interface
Line Rate: 2.048Mbps±50ppm
Line Code : HDB3
Interface Standard: ITU-T G.703
E1 Impedance: 75Ω(unbalance) or 120Ω(balance)
Connections : dual coax BNC and 120-ohm twisted-pair (RJ45)
Jitter tolerance : finer than G.742 and G.823
Fiber connector
Optical interface: SC/FC
Rate:10/100 adapt
Optical Wavelenth: FP1310 nm DFB1550nm+/-50/40nm
Sending consumption: -9dBm/-5dBm
Receiving and dispatching module:>-6dBm
Optical receiver receiving sensitivity: <-36 (BER<10-10):
Dynamic range receiving: >-30dB
Optical code:NRZ
Support several optical interface:
850nm/1310nm multi-mode fiber,
1310nm/1550nm single-mode fiber.
Transmit distance: multi-mode with 2KM, single-mode with 20KM,40KM, 60KM, and 120KM.
Power supply
working voltage range wide, good
anti-disturb and Isolation, work stable
option I – DC-48V,range DC-36V~DC-72C
option II – AC220V,range AC165V~AC240V
Power Consumption: <=3 Watts
Environment condition
Operating temperature: 0C~+50 C
Storage temperature: -20 C~+70 C
Relative temperature:95% (uncondensed)
Features:
( 1) Realize transparent transfer Ethernet data in 1-8 E1 channels ² 10M/100M Ethernet, full/half duplex self adapt, support VLAN.
(2) Ethernet support AUTO-MDIX( cross over and straight through self adapt)
(3)setting CRC alarm limitation to auto isolate lines with low transfer quality, single direction. When one direction error rate over limitation, disconnect only one direction, the other is not affected. Unbalance in two directions.
(4)Allow 1-4 E1 channels up to 10ms transfer delay. when the delay over the limitation, can stop transfer automatically.
(5)Having 2 loop back functions: E1 local loop, E1 external loop.
(6) Support Dynamic Ethernet MAC address(4096), having local address filter function.
(7)E1 interface compatible withITU-T G.703,G.704,and G.823. signaling slot not supported.
(8)E1 interface having internal clock resume circuit and HDB3 codec circuit.
(9)support E1 channel hot plug, and auto detect available E1 channels not pause the transmission.
(10)supporting 1-4 E1 channels customized configuration, auto detect the number of E1 channels and select the available E1 at reset.
(11) E1 Support 75Ω/unbalance impedance or 120Ω/balance for order
(12) support reset remote system from local system.
(13)having Ethernet monitor auto reset function.
(14)SNMP for option in chassis installation or built-in standalone
Technical Parameter:
E1 Interface
Line Rate: 2.048Mbps±50ppm
Line Code : HDB3
Interface Standard: ITU-T G.703
E1 Impedance: 75Ω(unbalance) or 120Ω(balance)
Connections : dual coax BNC and 120-ohm twisted-pair (RJ45)
Jitter tolerance : finer than G.742 and G.823
Fiber connector
Optical interface: SC/FC
Rate:10/100 adapt
Optical Wavelenth: FP1310 nm DFB1550nm+/-50/40nm
Sending consumption: -9dBm/-5dBm
Receiving and dispatching module:>-6dBm
Optical receiver receiving sensitivity: <-36 (BER<10-10):
Dynamic range receiving: >-30dB
Optical code:NRZ
Support several optical interface:
850nm/1310nm multi-mode fiber,
1310nm/1550nm single-mode fiber.
Transmit distance: multi-mode with 2KM, single-mode with 20KM,40KM, 60KM, and 120KM.
Power supply
working voltage range wide, good
anti-disturb and Isolation, work stable
option I – DC-48V,range DC-36V~DC-72C
option II – AC220V,range AC165V~AC240V
Power Consumption: <=3 Watts
Environment condition
Operating temperature: 0C~+50 C
Storage temperature: -20 C~+70 C
Relative temperature:95% (uncondensed)
Member Information
| Zhejiang Ebang Communication Co.,Ltd | |
|---|---|
| Country/Region: | Zhe Jiang - China |
| Business Nature: | Manufacturer |
| Phone: | 57130601 |
| Contact: | Nina Ding (sales engineer) |
| Last Online: | 11 Jan, 2012 |
