| Thermal shock test chamber |
|
| |
MS-CJ-50C |
MS-CJ-100C |
MS-CJ-200C |
MS-CJ-300C |
| Interior capacity(L) |
50 |
100 |
200 |
300 |
| System |
2-zone or 3 zone system by means of damper switching |
| Performance |
High temp. Chamber |
Pre-heat temp. Range |
+60℃～+200℃ |
| heating time※1 |
A+60℃→+200℃≤20min |
| Low temp. Chamber |
Pre-cool temp. Range |
-78℃～0℃ |
| Cooling time※1 |
A+20℃→-75℃≤70min |
A+20℃→-70℃≤80min |
| Test chamber |
Temp. uniformity |
±2℃ |
| Temp. Range |
A-65℃～+150℃ |
A-55℃～+150℃ |
| Temp. Recovery time※2 |
Within 5 minutes※3 |
Within 5 minutes※3 |
Within 5 minutes※3 |
Within 5 minutes※3 |
| Speciment capacity |
30kg |
| Speciment weight |
2.5kg |
7.5kg |
10kg |
7.5kg |
| Interior dimension(mm) |
W |
410 |
650 |
650 |
970 |
| H |
460 |
460 |
460 |
460 |
| D |
370 |
370 |
670 |
670 |
| Exterior dimension(mm) |
W |
1470 |
1710 |
1710 |
2030 |
| H |
1800 |
1800 |
1800 |
1800 |
| D |
1570 |
1570 |
1870 |
1870 |
| Utility requirements |
Temp.：+5℃～+35℃；Humidity：≤85%RH；Atmospheric pressure：86～106kPa |
| Material |
Enclosure |
Galvanized steel plain Sheet color coated |
| Interior |
Stainless steel plate SUS304 |
| Thermal insulant |
Hard urethane foam + glass wool |
| Construction |
High temp. Chamber |
Heater |
Nichrome Electronic Heater |
| Fan |
Centrifugal fan for High, ambient temperature.axial flow fan for pre-heating. |
| Low temp. Chamber |
Heater, condenser |
Nichrome Electronic Heater、condenser、Regenerator |
| Fan |
Centrifugal fan |
| Drivers |
Air cylinder |
Drive the ventilation door |
| Air compressor |
Provide compressed air to drive the air cylinder (Optional) |
| Refrigerator unit |
Refrigeration mode |
Mechanical cascade refrigeration system(water cooled) |
| Refrigerating Compressor |
Semi-closed refrigerating compressor |
| Refrigerant |
R404a/R23 |
| Condenser |
Stainless steel brazed plate heat exchanger |
| Controller |
Displayer |
86.37(Height)×115.17(Longth)mm，LCD |
| Running mode |
Program operation |
| Setting |
Touch panel method |
| Program capacity |
32 patterns, 3 steps max. per pattern, 999 times max. cycling. |
| Setting range |
High temperature upper limit:220℃；Low temperature limit：-80℃ |
| Test chamber：Shock upper limit+10℃，shock lower limit-10℃ |
| Display resolution |
Temp：0.1℃；Time：0.1min |
| Input |
thermocouple |
| Control mode |
PID control；BTC Blanced Temperature control |
| Power supply |
AC380(1±10%)V (50±0.5)Hz three-phase four-wire+ protection ground wire |
| Power(KW) |
38 |
36 |
36 |
36 |
| Weight(kg) |
1430 |
1480 |
1420 |
1530 |
| Cyclic cooling water |
Water pressure：0.25～0.4MPa， Water temperature：≤30℃ |
| Compressed air |
0.5～0.7MPa |
| Standard accessories |
Test chamber status indicator 1pc，time recorder 1pc，cable hole(Φ40)1pc，Casters with adjusters. |
| Safety devices |
Leakage breaker，Interior over heat protector，Fan over heat protector，Compressor over heat protector，Compressor over pressure protector，Speciment over heat protector，power supply protector |
| ※1 Heating time and cooling time is measured under high temperature chamber or low temperature chamber working only. |
| ※2 Recovery condition: Ambient temperature is +25℃ and cycling water temperature +25℃ |
| |
High Temperature chamber |
Low Temperature chamber |
Sensor position |
| ※3 Recovery time for high and low temperature chamber |
(+150℃：30minutes) |
(-65℃：30min) |
Upper side of speciment |
| Remarks: Above data maybe changed without notice. |
