Additive flame retardant and thermal conductivity silicone sealant
A/B HT-9802
HT-9802 A/B is a two-component silicone addition system thermalconductivity encapsulant, has the following characteristics:
1, plastic material at room temperature under the mixed storage time is longer, but in the heating conditions can be fast curing, especially for automatic production line.
2, temperature resistance, high temperature resistance, good. After curing (-50 ~ 200) temperature range, the silicone rubber was maintained and the insulation performance was excellent.
3, the curing process of small shrinkage, has a better waterproof, moisture and anti aging properties.
4, with the thermal conductivity, flame retardant properties of UL94-V0 grade.
A typical use: it is used for high power electronic components, for cooling and temperature resistant sealing protection requirements of high power module and a circuit board. Such as encapsulating module, automotive HID lamp power supply module, auto ignition system power supply module, solar panels, transformers, sensors and so on.
Two, technical parameters:
Performance index of A HT-9802 component B HT-9802 component
Appearance of white sticky black sticky body before curing
Viscosity (CPS) 1500 ~ 30001500 ~ 3000
Relative density (g/cm3) 1.65 ~ 1.50 ~ 1.65 ~ 1.50
A component: B component (weight ratio) 1:1
Curing type two-component addition
Mixed viscosity (CPS) 1500 to 3000
Operating time (min) 0.5h
The appearance of black elastomer after curing
Curing conditions (HR) 0.5h/80 or 3~4h/25
Solid
Of
After hardness (A Shore, 24hr) 45 + 5
Tensile strength (MPa = 1)
Waterproof level is greater than or equal to IP67
Expansion coefficient (PPM = 220)
Use temperature range (c) -50 ~ 200
Volume resistivity (CM) 1 x 1016
Dielectric strength (kV/, mm) = 23
Dielectric constant (1.2MHz) 2.9
Thermal conductivity (W/ (M - K)] = 0.60
Flame retardant grade UL94-V0
Three, the use of technology:
Two, according to the weight ratio of the 1 groups into the mixing tank mixing uniform.
2, the mixed good adhesive materials are filled in the sealing device, generally without the vacuum deaeration, if you need to get the high thermal conductivity, it is recommended vacuum deaeration after reperfusion. Room temperature or heating can be cured. The curing speed of glue and the curing temperature has a great relationship. It takes a long time to cure in winter. It is recommended that the heating method is used to cure, 30 minutes at 80 degrees, and about 3~4 hours in room temperature.
Four, note:
1, plastic material should be sealed storage. Mixed good adhesive should be used to avoid causing waste.
2, this product is a non dangerous goods, but not the entrance and eye.
3, after a long time, the filler will be in the plastic settlement. Please use after mixing evenly, do not affect the performance.
4, glue liquid contact with the following chemicals will make the glue is not cured:
1) N, P, S organic compounds.
2) Sn, Hg, Pb, As plasma compounds.
3) containing alkynes and multi vinyl compounds.
Five, packaging specifications: 50KG/ sets (A 25kg/ 25kg/, B plastic bucket)
Six, storage and transportation:
1, a cool dry place storage, storage period is 12 months (25 C).
2, such products are non dangerous goods, can be transported by the general chemical.
3. The A and B components of the colloid are required to be sealed and kept carefully in the transportation process!
4, more than the preservation period of the product should be confirmed that there is no exception to use.
The above performance data is the typical data measured in the laboratory environment of the temperature 25, humidity 70%, only for the use of the reference, and can not guarantee the full data in a specific environment, please customers in the use of experimental data as the standard.
