沙伯基礎PCABS

沙伯基礎PCABS
型號:6200
品牌:沙伯基礎
原產地:美國
類別:化工 / 樹脂
標籤︰PC+ABS , 沙伯基礎 , 改性PC
單價: ¥30 / KG
最少訂量:100 KG
發送查詢

產品描述

 

PC/ABS  C6200

 

 

 

 

CYCOLOY ™ Resin C6200

SI

British

Metric

PDF

Americas: COMMERCIAL

 

 

Non-chlorinated, nombrominated flame retardant PC/ABS offering balanced heat, flow and impact to meet various application needs.

 

 

Property

 

 

TYPICAL PROPERTIES (1)

MECHANICAL

Value

Unit

Standard

 

Tensile Stress, yld, Type I, 50 mm/min

680

kgf/cm²

ASTM D 638

 

Tensile Strain, brk, Type I, 50 mm/min

50

%

ASTM D 638

 

Flexural Stress, yld, 2.6 mm/min, 100 mm span

1050

kgf/cm²

ASTM D 790

 

Flexural Modulus, 2.6 mm/min, 100 mm span

27400

kgf/cm²

ASTM D 790

 

IMPACT

Value

Unit

Standard

 

Izod Impact, notched, 23°C

54

cm-kgf/cm

ASTM D 256

 

Instrumented Impact Energy @ peak, 23°C

622

cm-kgf

ASTM D 3763

 

Instrumented Impact Energy @ peak, -30

553

cm-kgf

ASTM D 3763

 

THERMAL

Value

Unit

Standard

 

HDT, 1.82 MPa, 3.2mm, unannealed

87

°C

ASTM D 648

 

HDT, 1.82 MPa, 6.4 mm, unannealed

90

°C

ASTM D 648

 

Relative Temp Index, Elec

85

°C

UL 746B

 

Relative Temp Index, Mech w/impact

85

°C

UL 746B

 

Relative Temp Index, Mech w/o impact

85

°C

UL 746B

 

PHYSICAL

Value

Unit

Standard

 

Specific Gravity

1.18

-

ASTM D 792

 

Mold Shrinkage, flow, 3.2 mm (5)

0.4 - 0.6

%

SABIC Method

 

Mold Shrinkage, xflow, 3.2 mm (5)

0.4 - 0.6

%

SABIC Method

 

Melt Flow Rate, 260°C/2.16 kgf

14.5

g/10 min

ASTM D 1238

 

Spiral Flow,260°C,10 ips,3.175 X 1524 mm

685.8

mm

-

 

ELECTRICAL

Value

Unit

Standard

 

Arc Resistance, Tungsten {PLC}

6

PLC Code

ASTM D 495

 

Hot Wire Ignition {PLC)

2

PLC Code

UL 746A

 

High Voltage Arc Track Rate {PLC}

3

PLC Code

UL 746A

 

High Ampere Arc Ign, surface {PLC}

0

PLC Code

UL 746A

 

Comparative Tracking Index (UL) {PLC}

2

PLC Code

UL 746A

 

Volume Resistivity

>1.E+15

Ohm-cm

IEC 60093

 

Surface Resistivity, ROA

>1.E+15

Ohm

IEC 60093

 

Dielectric Strength, in oil, 0.8 mm

35

kV/mm

IEC 60243-1

 

Dielectric Strength, in oil, 1.6 mm

25

kV/mm

IEC 60243-1

 

Dielectric Strength, in oil, 3.2 mm

17

kV/mm

IEC 60243-1

 

Relative Permittivity, 1 MHz

2.7

-

IEC 60250

 

Dissipation Factor, 50/60 Hz

0.004

-

IEC 60250

 

Dissipation Factor, 1 MHz

0.008

-

IEC 60250

 

Relative Permittivity, 50/60 Hz

2.8

-

IEC 60250

 

FLAME CHARACTERISTICS

Value

Unit

Standard

 

UL Recognized, 94HB Flame Class Rating (3)

0.71

mm

UL 94

 

UL Recognized, 94V-1 Flame Class Rating (3)

1.21

mm

UL 94

 

UL Recognized, 94V-0 Flame Class Rating (3)

1.47

mm

UL 94

 

UL Recognized, 94-5VA Rating (3)

3.4

mm

UL 94

 

UL Recognized, 94-5VB Rating (3)

2

mm

UL 94

 

 

Source GMD, last updated:2000/01/05

 

Processing

 

Parameter

Injection Molding

Value

Unit

Drying Temperature

80 - 90

°C

Drying Time

3 - 4

hrs

Drying Time (Cumulative)

8

hrs

Maximum Moisture Content

0.04

%

Melt Temperature

245 - 275

°C

Nozzle Temperature

245 - 275

°C

Front - Zone 3 Temperature

245 - 275

°C

Middle - Zone 2 Temperature

220 - 275

°C

Rear - Zone 1 Temperature

220 - 255

°C

Mold Temperature

60 - 80

°C

Back Pressure

0.3 - 0.7

MPa

Screw Speed

40 - 70

rpm

Shot to Cylinder Size

30 - 80

%

Vent Depth

0.038 - 0.076

mm

 

Source GMD, last updated:2000/01/05

 

• NOTE: Back Pressure, Screw Speed, Shot to Cylinder Size and Vent Depth are only mentioned as general guidelines. These may not apply or need adjustment in specific situations such as low shot sizes, thin wall molding and gas-assist molding.

 

 

THESE PROPERTY VALUES ARE NOT INTENDED FOR SPECIFICATION PURPOSES.

 

PLEASE CONTACT US FOR AVAILABILITY IN YOUR REGION.

(1) Typical values only. Variations within normal tolerances are possible for various colors. All values are measured after at least 48 hours storage at 23°C/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.

(2) Only typical data for selection purposes. Not to be used for part or tool design.

(3) This rating is not intended to reflect hazards presented by this or any other material under actual fire conditions.

(4) Internal measurements according to UL standards.

(5) Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.

(6) Needs hard coat to consistently pass 60 sec Vertical Burn. 
 

Disclaimer : THE MATERIALS, PRODUCTS AND SERVICES OF SAUDI BASIC INDUSTRIES CORPORATION (SABIC) OR ITS SUBSIDIARIES OR AFFILIATES (“SELLER”) ARE SOLD SUBJECT TO SELLER’S STANDARD CONDITIONS OF SALE, WHICH ARE AVAILABLE UPON REQUEST. INFORMATION AND RECOMMENDATIONS CONTAINED IN THIS DOCUMENT ARE GIVEN IN GOOD FAITH. HOWEVER, SELLER MAKES NO EXPRESS OR IMPLIED REPRESENTATION, WARRANTY OR GUARANTEE (i) THAT ANY RESULTS DESCRIBED IN THIS DOCUMENT WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (ii) AS TO THE EFFECTIVENESS OR SAFETY OF ANY DESIGN OR APPLICATION INCORPORATING SELLER’S MATERIALS, PRODUCTS, SERVICES OR RECOMMENDATIONS.  UNLESS OTHERWISE PROVIDED IN SELLER’S STANDARD CONDITIONS OF SALE, SELLER SHALL NOT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS MATERIALS, PRODUCTS, SERVICES OR RECOMMENDATIONS DESCRIBED IN THIS DOCUMENT. Each user is responsible for making its own determination as to the suitability of Seller’s materials, products, services or recommendations for the user’s particular use through appropriate end-use and other testing and analysis. Nothing in any document or oral statement shall be deemed to alter or waive any provision of Seller’s Standard Conditions of Sale or this Disclaimer, unless it is specifically agreed to in a writing signed by Seller.  Statements by Seller concerning a possible use of any material, product, service or design do not, are not intended to, and should not be construed to grant any license under any patent or other intellectual property right of Seller or as a recommendation for the use of any material, product, service or design in a manner that infringes any patent or other intellectual property right.

 

 SABIC and brands marked with ™ are trademarks of SABIC or its subsidiaries or affiliates.

 

© 2014 Saudi Basic Industries Corporation (SABIC). All Rights Reserved.

窗體底端

 

 

東莞市建和塑膠材料有限公司   黃生 13600184441

沙伯基礎PCABS  1

會員信息

東莞市建和塑膠材料有限公司
國家/地區︰广东省东莞市
經營性質︰貿易商
聯繫電話︰13600184441
聯繫人︰黃生 (經理)
最後上線︰2014/04/04

該公司相關產品信息