1. 遠紅外電熱膜用納米導電碳漿

nano conductive carbon paste used in far-infrared electric heat membrane

單一組分，加溫固化，優良的印刷性，對基材的附着力好，電熱狀態下功率穩定性好，發熱效率高，具有遠紅外功能，產品使用壽命長，適用於絲網、凹版等印刷方式。

（1）   長期工作溫度≤60℃：適用於PET、PI等電熱膜。實驗數據（僅供參考）：

連續通電30天，表面溫度60℃左右，無外控溫裝置，功率變化率<±2％。

（2） 長期工作溫度≤100℃：適用於環氧玻纖板等電熱板。實驗數據（僅供參考）：

連續通電30天，表面溫度100℃左右，無外控溫裝置，功率變化率<±3％。

（3）長期工作溫度≤100℃：適用於尼龍布等電熱布。實驗數據（僅供參考）：

連續通電30天，表面溫度100℃左右，無外控溫裝置，功率變化率<±2％。

（4）長期工作溫度≤140℃：適用於環氧玻纖板等電熱板。實驗數據（僅供參考）：

連續通電30天，表面溫度140℃左右，無外控溫裝置，功率變化率<±2％。

 以上四種導電碳漿屬於不同產品，同屬於電熱型導電碳漿，具體請來電來函咨詢。

Single component, curing with heat, excellent printability, excellent adhesion on substrate, power stability in the electric heat state is good,

high heat efficiency, far-infrared function, long service life, be suitable for printing patterns such as silk screen、intaglio printing and so on.

(1) Long-term working temperature ≤ 60 ℃: be suitable for electric heat membrane on the substrate of PET and PI and so on, Experimental data (reference only): galvanization Continuously for 30 days, surface temperature of about 60 ℃, without external temperature control device, rate of power change: <± 2%.

(2) Long-term working temperature ≤ 100 ℃: be suitable for electric heat board on the substrate of epoxy and so on, Experimental data (reference only): galvanization Continuously for 30 days, surface temperature of about 100 ℃, without external temperature control device, rate of power change: <± 3%.

(3) Long-term working temperature ≤ 100 ℃: be suitable for electric heat Cloth on the substrate of nylon and so on, Experimental data (reference only): galvanization Continuously for 30 days, surface temperature of about 100 ℃, without external temperature control device, rate of power change: <± 2%.

(4) Long-term working temperature ≤ 140 ℃: be suitable for electric heat board on the substrate of epoxy and so on, Experimental data (reference only): galvanization Continuously for 30 days, surface temperature of about 140 ℃, without external temperature control device, rate of power change: <± 2%.

Four conductive carbon pastes above belong to different kinds of product, but all belong to electric heat conductive carbon paste, welcome to call us for details.

2. 薄膜開關等柔性線路板用導電碳漿 

conductive carbon paste used in membrane switch FPC

單一組份，可供方阻：10Ω/□～10MΩ/□，優異的柔韌性、印刷性及附着力，表面硬度高，阻值持久穩定性高，受溫度影響阻值變化極小，具體歡迎來電來函咨詢。

Single component, available square resistance：10Ω / □～10MΩ / □,excellent flexibility、printability and adhesion,surface hardness and lasting stability of resistance are high, resistance changes affected by temperature is little, welcome to call us for details.

3. 觸摸屏、冷光片等用導電碳漿

conductive carbon paste used in Touch screen and EL film

單一組份，可提供阻值很低，對ITO膜、PET膜、玻璃等的附着力優異，固化溫度低，固化時間短，表面硬度高，具體歡迎來電來函咨詢。

Single component, very low available resistance, excellent adhesion on

ITO film、PET film and glass ect., low curing temperature, short curing

time, high surface hardness, welcome to call us for details.

4. 太陽能電池用導電碳漿

conductive carbon paste used in solar battery

單一組份，對基材玻璃、單（多）晶硅片等的附着力優異，耐高壓、高溫、高濕等，大功率，產品的穩定性高，使用壽命長，具體歡迎來電來函咨詢。

Single component, excellent adhesion on Single (multi) silicon wafer and glass, be able to bear high voltage、high temperature and high humidity ect., large power,high product stability, long service life, welcome to call us for details.

5.  檢測試劑條用導電碳漿

conductive carbon paste used in detection reagent strips

單一組份，加溫固化，可供方阻10Ω/□～10MΩ/□，優異的印刷性及附着力，表面硬度高，耐磨性好，阻值持久穩定性高，檢測敏感性好，具體歡迎來電來函咨詢。

Single component, curing with heat, available square resistance：10Ω / □～10MΩ / □, excellent printability and adhesion, high surface hardness, good abrasion, lasting stability of resistance are high, good Detection sensitivity, welcome to call us for details.

6. 燈管等光源用導電碳漿

conductive carbon paste used in lamp light

對燈管的附着力高，耐摩擦性能優異，耗電量更小，亮度更高，具體請來電來函咨詢。

high adhesion on lamp ,excellent performance of abrasion, smaller power consumption, higher brightness, welcome to call us for details.