廣州市連承復合材料有限公司
GuangZhou LianCheng Composites CO.,LTD.
(原廣州市連平玻璃鋼材料有限公司)
地址 :廣州市荔灣區芳村大道西402號
Tel : 020-81761238 / 020-81754069 Fax : 020-81761045
POLYLITE OD-R-449
透明鑄塑品用的不飽和聚酯樹脂
DESCRIPTION 一般說明:
Polylite OD-R-449 is a low viscosity, non-promoted, three component unsaturated polyester resin, designed for transparent casting.
OD-R-449是一種低粘稠性、不含促進劑、三組分的不飽和聚酯樹脂,設計用於生產透明鑄塑品。
CHEMICAL COMPOSITION 化學成分:
The mainly reaction raw materials are Styrene Monomer, Phthalic Anhydride, Maleic Anhydride.
不飽和聚酯樹脂Polylite OD-R-449的主要化學成分有苯乙烯、苯酐和順酐。
LIQUID PROPERTIES﹝
Appearance 外觀 : Transparent Liquid透明液體
Viscosity (Poise) 粘度 : 3 - 5
Color (Harzen) 黑曾氏色度 : Max 最大60
Gel time (Min) 膠凝時間 * : 5 – 9 min.分鐘
* 6% Cobalt 濃鈷(促進劑)
55% MEKPO 過氧化鉀乙酮
Specific Gravity 比重 : 1.11
PROPERTY of CURED RESIN
固化樹脂的特性:
Specific gravity 比重 ASTM-D-792 : 1.21
Barcol hardness 巴科爾硬度 J-934-1 : 35
Heat destroy 熱畸變溫度 ASTM-D-648 :
Water absorption (24h) 吸水率 ASTM-D-570 : 0.25%
Flexural strength 揉曲強度 ASTM-D-790 :
Flexural modulus 揉曲模量 ASTM-D-790 :
Tensile strength 拉伸強度 ASTM-D-638 :
Tensile modulus拉伸模量 ASTM-D-638 :
Elongation 伸長率 ASTM-D-638 : 2.1%
Compressive strength 壓縮強度 ASTM-D-695 :
Charply Impact strength 夏皮衝擊強度 JIS-K-6911 :
RECOMMENDED FORMULATION 建議配方:
Commodity 商品 | 重量份數 | |
Polylite OD-R-449 | 不飽和聚酯樹脂 | 100 |
Accelerator RP-126 | 促進劑 | 0.3 – 0.5 |
55% MEKPO | 過氧化鉀乙酮 | 0.3 – 0.5 |
Gel Time 膠凝時間﹝ | 40 – 60 min分鐘 |
SPECIAL TERMS 特別注意事項:
1. Preferably gel time and exotherm should be controlled by additional amount of MEKPO and not by Accelerator RP-126.
必須用過氧化鉀乙酮之添加量來控制最好的膠凝時間和放熱量,而不是用促進劑。
2. In case of big casting, amount of MEKPO should be lowered down to 0.3% because of excess exotherm.
鑄制大型產品時,一定要把過氧化鉀乙酮的添加量下降到0.3%,因為放熱量過高,產品會爆裂。
3. Casting should be post-cured after 20〜24 hours from exotherm stage.
鑄件需要經過20〜24小時的放熱固化定型。
適合用作模具的材料為聚丙烯、金屬、玻璃及玻璃鋼等。如果用聚乙烯、聚氯乙烯和硅酮樹脂製成的模具,因樹脂OD-R-449與該等材料有粘性反應,不能生產透明產品。
1. Mixed resin is gelled up to
將混和備用樹脂OD-R-449倒入直徑10釐米、高20毫米的圓形模具達至7毫米高,固化形成第一層。
2. Butterfly wetted with styrene monomer is put on the first cast. Then the resin is poured and gelled up to top of the watch dish, which is sealed with glass plate.
把用苯乙烯濕潤的蝴蝶放在第一層上,再倒入混和備用樹脂至模具的最高位,以玻璃片封口等待膠凝。
3. Exotherm is completed and the cast is post-cured for 12 hours at
已膠凝完成放熱的鑄件需進行12小時固化定型,接著脫模、水磨和拋光。
SAFETY安全指引:
1. Polylite OD-R-449 must be kept away from open flames and direct sunlight. 遠離明火及避免直接陽光
2. It is recommended that the storage temperature should not exceed
建議儲存在
3. In case of skin contact, wash thoroughly with soap and water. In case of eye contact, flush promptly with copious amounts of water and consult a physician. 如果接觸皮膚,可用肥皂和水徹底沖洗。萬一淺入眼 睛,應用大量清水沖洗及求醫診治。
廣州市連承復合材料有限公司 | |
---|---|
國家/地區︰ | 广东省广州市 |
經營性質︰ | 貿易商 |
聯繫電話︰ | 15975628547 |
聯繫人︰ | 李先生 (業務) |
最後上線︰ | 2010/12/30 |