Model: | LH105 |
---|---|
Brand: | Lianhuan |
Origin: | Made In China |
Category: | Chemicals / Rubber Materials |
Label: | RTV-2 Potting Compou , PCB Electronic Potti , Electronic potting c |
Price: |
¥75
/ kg
|
Min. Order: | 2 kg |
RTV silicone rubber for LED and solar (PV) panels used for
Electronic components surface
For materials of PC(Poly-carbonate)
PP,ABS,PVC
Metal materials.
Feature of RTV silicone rubber for LED and solar (PV) panels
Good Viscosity
Inherent flame resistance
two components addtion cured potting silicone with heat-conducting
cures with both on room temperature and heated temperature
higher temperature the faster of the curing time
applied to electronic components for insulation
waterproofing, fixed and flame retardant.
Typical Application of RTV silicone rubber for LED and solar (PV) panels
RTV silicone rubber for solar (PV) panels could be applied to
- high powered electronics,
- DC/DC module and circuit board which requires heat dissipation and high temperature resistance.
-It can be broadly used for LED screen, Wind Power Generator, PCB substrate, etc.
Technical Parameters of RTV silicone rubber for LED and solar (PV) panels
Features |
5035 A |
5035 B |
|
Before Curing |
Appearence |
Gray Fluid |
White Fluid |
Viscosisty(25°Ccps) |
65000±500 |
800±500 |
|
Operation features |
Mixing Ratio |
10:1 |
|
Viscosisty(after mixing) (cps) |
2000~3000 |
||
Operating Time(25°C hr) |
2 |
||
Curing time (min,25°C) |
48 |
||
Curing time(80°C hr) |
20 |
||
After Curing |
Hardness(Shore A) |
42±3 |
|
Thermal conductivity [W(m·K)] |
≥0.8 |
||
Dielectric Strength(KV/mm) |
≥25 |
||
Permittivity(1.2MHz) |
3.0~3.3 |
||
Volume Resisivity(Ω·cm) |
≥1.0×1016 |
||
linear expansibility [m/(m·K)] |
≤2.2×10-4 |
||
Fire Resistance |
94-V1 |
(Pls note: the above data for this product in 25 °C temperature, 55 percent humidity conditions, for reference)
TECHNICAL GUIDELINES of RTV silicone rubber for LED and solar (PV) panels
1, Pls put part A and part B in separate container and stir evenly before mixing the two part together.
2, Mixing Ratio: part A: part B = 10:1B
3, De-air in vacuum pump under 0.08 MPa for 3-5 minutes.Then the mixture could be used for pouring.
4,Pls note that the thickness of the silicone affects the curing time. If the silicone used is a little thick,then the curing time will be a little longer.The temperature also affects the curing time.When in lower temperature, we s est customers appropriately heat the mixture to accelerate vulcanization. With temperature of 80~100°C, the silicone will cure in 15 minutes; while in 25°C room temperature, the silicone will cure around 8 hours.
Notes:
1.Pls use after the test. When necessary, pls clean the application areas.
2. LH 5035 A should seal storage. The mixture should be used up disposably to avoid causing waste.
3.LH 5035 A belongs to non-dangerous goods,
but keep away from mouth and eyes.
RTV silicone rubber for LED and solar (PV) panels used for
Electronic components surface
For materials of PC(Poly-carbonate)
PP,ABS,PVC
Metal materials.
Feature of RTV silicone rubber for LED and solar (PV) panels
Good Viscosity
Inherent flame resistance
two components addtion cured potting silicone with heat-conducting
cures with both on room temperature and heated temperature
higher temperature the faster of the curing time
applied to electronic components for insulation
waterproofing, fixed and flame retardant.
Typical Application of RTV silicone rubber for LED and solar (PV) panels
RTV silicone rubber for solar (PV) panels could be applied to
- high powered electronics,
- DC/DC module and circuit board which requires heat dissipation and high temperature resistance.
-It can be broadly used for LED screen, Wind Power Generator, PCB substrate, etc.
Technical Parameters of RTV silicone rubber for LED and solar (PV) panels
Features |
5035 A |
5035 B |
|
Before Curing |
Appearence |
Gray Fluid |
White Fluid |
Viscosisty(25°Ccps) |
65000±500 |
800±500 |
|
Operation features |
Mixing Ratio |
10:1 |
|
Viscosisty(after mixing) (cps) |
2000~3000 |
||
Operating Time(25°C hr) |
2 |
||
Curing time (min,25°C) |
48 |
||
Curing time(80°C hr) |
20 |
||
After Curing |
Hardness(Shore A) |
42±3 |
|
Thermal conductivity [W(m·K)] |
≥0.8 |
||
Dielectric Strength(KV/mm) |
≥25 |
||
Permittivity(1.2MHz) |
3.0~3.3 |
||
Volume Resisivity(Ω·cm) |
≥1.0×1016 |
||
linear expansibility [m/(m·K)] |
≤2.2×10-4 |
||
Fire Resistance |
94-V1 |
(Pls note: the above data for this product in 25 °C temperature, 55 percent humidity conditions, for reference)
TECHNICAL GUIDELINES of RTV silicone rubber for LED and solar (PV) panels
1, Pls put part A and part B in separate container and stir evenly before mixing the two part together.
2, Mixing Ratio: part A: part B = 10:1B
3, De-air in vacuum pump under 0.08 MPa for 3-5 minutes.Then the mixture could be used for pouring.
4,Pls note that the thickness of the silicone affects the curing time. If the silicone used is a little thick,then the curing time will be a little longer.The temperature also affects the curing time.When in lower temperature, we s est customers appropriately heat the mixture to accelerate vulcanization. With temperature of 80~100°C, the silicone will cure in 15 minutes; while in 25°C room temperature, the silicone will cure around 8 hours.
Notes:
1.Pls use after the test. When necessary, pls clean the application areas.
2. LH 5035 A should seal storage. The mixture should be used up disposably to avoid causing waste.
3.LH 5035 A belongs to non-dangerous goods,
but keep away from mouth and eyes.
4. When it gets stratified after a period of storage, Please mix it evenly before using, which does not affect the performance.
SHELF LIFE AND TRANSPORTATION for LED and solar (PV) panels silicone
1. Twelve(12) months when stored at 24C in tightly closed original packages.
2. This kind of product is non-dangerous product, which could be transported as general chemicals.
3. Please consult the supplier after Storage beyond the expired date
4. When it gets stratified after a period of storage, Please mix it evenly before using, which does not affect the performance.
SHELF LIFE AND TRANSPORTATION for LED and solar (PV) panels silicone
1. Twelve(12) months when stored at 24C in tightly closed original packages.
2. This kind of product is non-dangerous product, which could be transported as general chemicals.
3. Please consult the supplier after Storage beyond the expired date
Any question ,please feel free to contact MS Betty zhou
TEL:0086-755-29498683
FAX:0086-755-27052562 skype:analiu2012
Cell/whatsapp/wechat:0086-13620997228
Payment Terms: | TT |
---|---|
SHENZHEN LIANHUAN SILICONE MATERIAL CO.,LTD | |
---|---|
Country/Region: | Guang Dong - China |
Business Nature: | Manufacturer |
Phone: | 13620997228 |
Contact: | analiuqun (salesman) |
Last Online: | 02 Aug, 2017 |