obd ii gps tracker

Model:	XH-007
Brand:	fsaar
Origin:	Made In China
Category:	Electronics & Electricity / Other Electrical & Electronic
Label:	obd , gps , tracker
Price:	US $57 / pc
Min. Order:	1 pc

Inquire Now

Product Description

Safety Information

12V Working power supply, unable install to 24V or more higher Battery Voltage, otherwise will burn up circuit and not in Warranty
Prior to the moving of the vehicle and the engine ON to install the device
No raining or high temperature exposure, and unable to take this product under metallic shield’s place when installing. If the OBD port in User’s car disturbs the driver drives his car when connect the OBD device, or the OBD port is located in a deeper place of Center Console and can’t get the GPS signal, the user should use an extension cord to prolong it to a hidden place of car
The product complies with the relevant Chinese standard of electromagnetic compatibility. However, please keep away from electronic equipment which is likely to be disturbed by the wireless signal, to avoid the signal interruption
Switch off this product in any area marked “ Explosive “, “ might explode “, “ closed wireless transceiver devices “ etc ( such as the hospital, gas station and airport )
Do not dispose the product in a fire, otherwise ,it may cause the battery explosion
Keep the product and accessories out of the reach of Children

Function Introduction

XH007 is equipped with OBD diagnostic GPS tracker, which set a multiple function of anti-theft, fault diagnosis, monitoring, emergency alarm and tracking in its entirety, also with compact size, standard OBD port to connect vehicle, and quick install etc... Widely used for vehicle location management, vehicle fault early warming, vehicle detection, fuel consumption statistics and safe drive auxiliary analysis.

Car OBD Port

Features:

1. GPS location / Vehicle Fault self-diagnosis alert function/ GSM remote management of Report, specialized design for private car。

2. Quick install, plug and play。

3. Obtain mileage, vehicle fuel consumption, engine revolution speed, temperature, travel speed and fault code etc. Data, also display it on remote surveillance software by remote meter.

4. GPS, GSM and LBS assistant position system.

5. Inbuilt 8MB Flash, to reserve the gps data if no gsm signal and upload it later upon getting the signal again —blind access capabilities.

6. Multiple location modes :

Fixed time location + Degree/Turns report

Fixed time location+ Distance+ Degree/Turns report

Distance + Degree/Turns report (save up the flow of GPRS, low data traffic)

7. 3D Acceleration sensor determines the vehicle emergency brake status.

8. 10000PCS GPS track records to TF card.

9. Report DTC fault code to Surveillance Center and record it to TF card.

10. Vehicle battery voltage too low alarm and engine temperature too high alarm.

文本框: 2. Host appearance description

1. microphone
2. GSM network indicator light
3. GPS indicator light
4. OBD work indicator light

3. Accessories

No.	photoes	NAME	note
1		OBD Tracker	1 pc
3		Velcro	1 pc
4		CD	Including manual and Web manual
5		Packing Box
6		OBD extension	1 pc
7		OBD manual	1 pc

4. Specification

Content	Specification
Dimension	57x51x27 mm
Weight	60g
Network	EDGE,GSM/GPRS
Net frequency	EDGE/GPRS/GSM 850/900/1800/1900 MHz
GPS chip	UBLOX NEO-M6
GPS sensitivity	-162dBm
GPS accuracy	5m
OBD specification	OBD II/EOBD
Time to first initiate	Cold status 45s Warm status 35s Hot status 1s
Sensor	Shock sensor, Acceleration sensor
Memory	8MB
Input Voltage	12V DC Input
Built -in Battery	Chargeable changeable 3.7V 150mAh Li-ion battery
Standby time	48hours
Storage Temp.	-40°C to +85°C
Operation Temp.	-20°C to +55°C
Humidity	5%--95% non-condensing

Indicator status description

The operation status represented by indicator light are as below：

Indicator	Action	Status
GSM network Indicator	Slow flicker	Connect the network after starting system
	Always on	GSM network failed
	5 seconds off, 1 second light	GSM signal is OK
GPS signal Indicator	Always on	GPS signal searching
	No lights	No GPS signal
	5 seconds off, 1 second light	GPS signal is OK
OBD function Indicator	Always on	OBD function is OK
OBD function Indicator	No lights	when you use the device over 1 minutes first time , means match it unsuccessful with OBD protocol

The device applies to:

Including all of Compatible OBDII /EOBD vehicles except for the model as below:
1. After 1996, U.S. production of gasoline vehicles.
2. After 2003, all of China production of gasoline Vehicles.

3. After 2001, or after 2000, Europe production of gasoline vehicles.

After 2004, or after 2003, Europe production of diesel vehicles.

5.Operating Instructions

First Steps: SIM card installation

Make sure that there is no call transfer, incoming call display is on, and PIN code turned off... SMS must be plain text, can not recognize the PDU form.

Open the SIM rear cover，Put the SIM card into the holder, and turn the foil right and fasten it in place.

Second Steps: Plug the device to vehicle OBD II port.

If the OBD port is located in a deeper place of vehicle frame to influence getting GPS signal, please prolong the extension cord to a better place to get a good GPS signal, and fix it with Velcro.

6 Boot devices

Plug the device to the OBDII port, the device will tick, then GSM indicator will blink, next the device will search GSM and GPS signal and begin to work normally after 10 to 40 seconds

TO check the OBD indicator lights or not, the device will search the OBD protocol of the vehicle automatically when pl ing the vehicle first time and the time is about 1 minute more or less

The OBD indicator lights will always on if finding the matched OBD protocol

GPS indicator will blink when the device get the GPS signal, you can set any commands in the manual

6.1 Initiation

Send SMS “#begin#password#” to device, it will reply “System Recover successfully” and initialize all the settings.

6.2 change the password

Send SMS“#password#old password #new password#” to change the password.

After sending successfully the device will reply with “The password has been successfully changed. The new password is ****”.

6.2.2 Be sure keep the new password in mind, you should set the device to the factory setting if missing the new password.

6.2.3 Make sure the new password is in 4 digits, otherwise the tracker can not recognize the password.

6. 3 Authorization

Max five numbers to be authorized.

6.3.1 Master setting

Send SMS“#master#” the device will act the cell phone number as the authorized number。If set successfully, the device will reply

“welcome use GPS tracker ,the password is 1234”

6.3.2 General user setting

Send SMS“#user#phone number#”. All the other authorized number is set by the first authorized number. If set successfully, will reply “The user number has been successfully changed. The new number is: **********.”

6.3.3 change master：

send SMS “#new master# the administrator’s number ( which want to change)#”, if the number authorizes successfully , the device will reply “The new master number have been changed successfully, the new number is ********.”

6.3.4 delete user：

Send SMS “#deluser # authorized number(which want to be delete)#” ,if the number deletes successfully, the device will reply “Delete the user number *********successfully”.

6.3.5 Set SMS alarm number

6.3.5.1 Send SMS alarm number “#center#phone number#".

After setting successfully, the device will reply with “SMS alarm number set successfully”.

Set SMS alarm number, when car in ACC OFF state. And arm device, If Shock sensor trigger will send alarm SMS to this mobile phone number.

6.3.5.2 Send SMS alarm number “#delcen#, after setting successfully, the device will reply with “SMS alarm number delete successfully”.

6.4 Single locations

6.4. 1 If without any authorized number, any mobile numbers dial the device, it will reply Latitude and longitude information;

If set the authorized number, non-authorized numbers dial the device won’t reply Latitude and longitude information

6.4.2 Dialing the device with an authorized number, it will hang up and reply a real-time Geo-info as below：

Lat: 22.636027N Long: 114.032210E, speed: 023.0 direction: 270.0 Tim: 13/09/09 12:00

http://maps.google.com/?q=22.636027N, 114.032210E

(Means latitude, longitude, speed, direction and time)

URL：mobile phone click the URL link in the positioning message, can view the location map of the device (mobile phone must support WAP get online function)

6.5 Anto track

6.5 .1 Anto track

1. Send SMS“#auto#030s#005n#”to the device, it will report the Geo-info at 30s intervals 5 times.(s: second, m: minute, h: hour). The setting must be in 3 Arabic numbers and the maximum value is 255 times

6.5.2 Unlimited positioning

Send SMS “#auto#030s#***n#” to the device, it will reply SMS heaps of times

6.5.3. cancel ：

send SMS“#offtn#”to the device.

Remark: Time interval must be more than 20 seconds.

6.5.4 Blind Access Capabilities

If there is no GSM signal, or the GPRS is offline, the device will

Save the current GPS tracking message to the flash memory automatically. When the device gets the signal again, and the device is in GPRS mode, will upload the GPS historical data information automatically.

6.6 Monitoring

This function is the user dialing the device, then can listen what happen around the device

6.7 Convert command “track” and”monitor” between the two modes.

6.7.1 Default state“track”（location mode）

6.7.2 Send SMS“#monitor# ”to the device,will reply“monitor ok!”，change to monitor mode.

6.7.3 Send SMS #track#” to the device,will reply “track ok!” Return to the locate mode.

6.8 Check IMEI

Send SMS “#imei#” to the device.

6.9 Status Report

Function	Description
Degree Report	Default 30°，can set between 5 to 180°.When the vehicle turns a corner that exceed the parameter you set, will send the GPS location data to platform, to improve the track data if failing to send the track information in time
Distance Report	Default 2000meter. Can set between 100 to 100000 meters. When the vehicle exceeds the Degree you set, will become ZERO and re-calculate it again
Mileage Report	Each GPRS data packet contain the mileage information, you should modify the initial mileage value to current mileage of vehicle to make it synchronization when you use the device first time
Emergency Brake & Acceleration Report	Built-in acceleration sensor, can determine vehicle acceleration and emergency brake acceleration threshold
100 km Fuel Consumption	Each GPRS data packet contain 100km fuel consumption (current speed), to evaluate Vehicle fuel consumption

Alarm Function and Warning function

Function	Description
Movement Alarm	the device stays a place 3-10 minutes and illegal movement of 200 meters, will report it to platform or on mobile
Over speed Alarm	the vehicle speed exceeds the speed threshold you set will trigger over speed alarm, and report it to platform or tick on the spot
Illegal demolition Warning	Someone demolish the device from the OBD port illegally, will report it to the mobile of master
Engine revolution speed too high Warning	device upload real-time data. platform extended function
Coolant temperature too high Warning	device upload real-time data. platform extended function
Battery voltage too low Warning	device upload real-time data. platform extended function
Vehicle Fault alarm	report default code (DTC ） to platform

6.10 Movement alarm:

Setting: When the device stays immobile in a place for 3-10 minutes, the user can send SMS“#move#” to the device, and then the device will reply “move alarm setting successfully!” It will reply SMS “Move+ the Geo-info to the authorized numbers upon the device move over 200 meters .Also, will send alarm SMS every 3 minutes

Cancel: Send SMS “#offmove#” to cancel the movement alarm

6.11 Over speed alarm:

Setting: Send SMS “#speed#080#” to the device(suppose 80km/h), and it will reply“speed ok!” . The device will send SMS “speed+080!+Geo-info to the authorized numbers when the driving speed over 80km/h . Also, will send an alarm SMS every 3 minutes. And will cancel the alarm automatically if the vehicle speed decelerates below the setting parameters

Cancel: Send SMS “#offspeed#” to cancel over speed alarm.

Remark: Recommended setting of over speed alarm 50km/h or over, GPS signal may be not accurate because of drifting if Vehicle speed is too slow.

6.12 Illegal demolition Warning:

The device is demolished illegally; the device will reply “External power shut off” to the authorized mobile number.

6.13 Vehicle fault alarm:

When the vehicle fault happen will trigger vehicle fault alarm, the device will upload fault code to platform; the user can check the corresponding fault meanings of fault code library on the platform, and then can find the fault in advance to avoid greater risks

6.14 Modify time:

Send SMS: “#time#time zone#”，it will reply “ time is set successfully” if it is successfully set. It will reply: “Time zone OK”

6.15 Initial mileage setting:

If we want to be on the mileage meter platform mileage value and vehicle

Meter synchronization, so we have to do the following Settings:

Send SMS: “#mileage#mileage value#”，it will reply “ initial mileage set successfully”

For example : if send this SMS:“#mileage#1200# to device, Mean vehicle meter mileage the current value is 1200KM.

6.16GPRS setting:

Generally, user don’t need to set the server parameter before use, the factory has set the right server parameter. If the tracker can’t connect server, please reference to the following:

6.16.1 Setting an IP address and port:

Send SMS “#ip #IP address #port#”

If set up successfully, the tracker will reply SMS “setting IP address ,port set up successfully”.

For example: " #adminip # 123.183.212.133 #8067# ” (Default Mode)

Cancel: Send SMS "#delip#" to cancel the setting, It will reply “IP address delete successfully”.

6.16.2 Setting APN

Send SMS “#apn#APN CONTENT#user name#password#”, as long as APN has been set successfully the tracker will reply SMS“APN setting successfully”.

For example :Send SMS “#apn#safaricom#saf#data# " it will reply “APN ok”.

6.17 SMS Mode & GPRS Mode

Send SMS "#smgp#1#" for SMS mode. (Default Mode)

Need to send SMS "#smgp#0#" to set up GPRS mode if you use software of monitoring center on PC.

Please reference to monitoring software instruction of the disk after set up GPRS mode.