SHR E-LIGHT

ANACUADA SHR E-LIGHT hair removal

Advantages of SHR machine:

1. SHR is with STABLE PULSE mode can emit energy averagely, however multi-pulse IPL under SHR model is better focus on very stable energy(not high, not too low), which is very safe for patients

2. SHR filtered violet light and infrared light, which will eradiate and absorb water from target skin. So SHR does not have any side-effect to body.

3. with DEC technology. Identified function makes operation simple, and makes treatment safely!

4. with bigger frequency (from 1 to 10Hz), Which accelerate operation speed and short a lot of time for treatment!

5. with Stationary technology & In-motion technology. Moving IPL can use less time to do treatment on back, leg and arm.

Applications

1. Therapy acne

2. Reduction of vascular lesions

3. Reduction of pigmented lesions

4. Skin rejuvenation

5. Permanent hair removal

6. Wrinkle removal

7. Breast Treatment

Specification

Wavelength 430/530/560/580/640-1200(nm)

Handpiece number 2 piece with 5 filters

Spot size 12*30mm&15*50mm

Cooling system semiconductor+air+water+cooling gel

IPL light energy 1-50(J/cm²)

Pulse Duration 1-10ms

Pulse NO. 1-6

Skin cooling -4°c-10°c

Display 10.4"color touch screen

Output power 3000W

SHR width 1-7ms

SHR frequency 1-10HZ

Voltage 110V,50HZ or 220V,60HZ

Machine Size (L*W*H):42cm*38cm*50cm

Net weight 25kg

Hand-piece and Application

Wavelength Treatment

430-1200nm Acne removal

480-1200nm Age spots, sun spots & pigmentation removal, skin rejuvenation

530-1200nm Freckles removal, Skin rejuvenation

560-1200nm Whitening skin, Skin rejuvenation

580-1200nm Vascular removal, fade melasma, skin rejuvenation

640-1200nm Thick Hair removal

690-1200nm Soft Hair removal

Working Function

1, Hair removal

1. Cut or shave hair to 1-2mm or ask patients to shave at home 2-3 days before treatment.

2. Clear treatment area.

3. Turn on machine,

1). Use SHR, adjust pulse width at 7ms, frequency 5HZ, energy 10J/cm2.

2). Use normal hair removal treatment, put the 640nm or 690nm filter into the slot, select "hair removal”, adjust the parameter, set it to ‘ready’.

4. Put cooling gel on treatment area about 2mm.

5. Wear protecting goggles for patient and operator.

6. Shot the treatment area, let the crystal tip to touch cooling gel, you are permitted to have 1/3 overlapping on treatment area.

7. Wipe off cooling gel after treatment and clear treatment area with cooling water. If patients feel warm or hot, you may put ice bag on treatment area until heat disappears.

2, Skin rejuvenation

1. Clear treatment area.

2. Turn on machine ,put the 560nm filter into the slot, select "skin rejuvenation",adjust the parameter, set it to ‘ready’ .

3. Put cooling gel on treatment area about 2mm, you are s ested to put cooling gel in refrigerator to keep temperature of gel during 0-4°C.

4. Wear goggles for patient and operator

5. Shot the treatment area, let the crystal tip to touch cooling gel. You are permitted to have 1/3 overlapping on treatment area.

6. Wipe off cooling gel after treatment and clear treatment area with cooling water. If patients feel warm or hot, you may put ice bag on treatment area for 30 minutes until heat-feeling disappears.

3, Pigmentation Therapy
1. Clear treatment area.

2. Turn on machine ,put the 480nm or 530nm filter into the slot, select "pigmentation

therapy",adjust the parameter, set it to ‘ready’ .

3. Put cooling gel on treatment area about 2mm, you are s ested to put cooling gel in refrigerator to keep temperature of gel during 0-4°C.

4. Wear goggles for patient and operator

5. Shot the treatment area, let the crystal tip to touch cooling gel. You are permitted to have1/3 overlapping on treatment area.

6. Wipe off cooling gel after treatment and clear treatment area with cooling water. If patients feel warm or hot, you may put ice bag on treatment area for 30 minutes until heat-feeling disappears.

4, Vascular Therapy
1. Clear treatment area.

2. Turn on machine ,put the 580nm filter into the slot, select "vascular therapy",adjust the parameter, set it to ‘ready’

3. Put cooling gel on treatment area about 2mm, you are s ested to put cooling gel in refrigerator to keep temperature of gel during 0-4°C.

4. Wear goggles for patient and operator

5. Shot the treatment area, let the crystal tip to touch cooling gel. You are permitted to have 1/3 overlapping on treatment area.

6. Wipe off cooling gel after treatment and clear treatment area with cooling water. If patients feel warm or hot, you may put ice bag on treatment area for 30 minutes until heat-feeling disappears.

5, Acne Therapy

1. Clear treatment area.

2. Turn on machine ,put the 430nm filter into the slot, select "acne therapy",adjust the

parameter, set it to ‘ready’ .

3. Put cooling gel on treatment area about 2mm, you are s ested to put cooling gel in refrigerator to keep temperature of gel during 0-4°C.

4. Wear goggles for patient and operator

5. Shot the treatment area; let the crystal tip to touch cooling gel. You are permitted to have 1/3 overlapping on treatment area.

6. Wipe off cooling gel after treatment and clear treatment area with cooling water. If patients feel warm or hot, you may put ice bag on treatment area for 30 minutes until heat-feeling disappears.

Wrinkle removal

1. Clear treatment area.

2. Turn on machine ,put the 580nm filter into the slot, select "wrinkle removal",adjust the parameter, set it to ‘ready’

3. Put cooling gel on treatment area about 2mm, you are s ested to put cooling gel in refrigerator to keep temperature of gel during 0-4°C.

4. Wear goggles for patient and operator

5. Shot the treatment area, let the crystal tip to touch cooling gel. You are permitted to have 1/3 overlapping on treatment area.

6. Wipe off cooling gel after treatment and clear treatment area with cooling water. If patients feel warm or hot, you may put ice bag on treatment area for 30 minutes until heat-feeling disappears.